Yamaha RX10RL Скачать руководство пользователя | Manualshive

Страница: 21 / 99

background image

5-2

ESU00361

Engine overheating prevention system

This model is equipped with an engine overheating pre-
vention system to prevent overheating when the engine
is idling.
When the engine has been idling for at least 3 minutes
and the coolant temperature has risen above 100 °C
(212 °F), the engine automatically shuts off to prevent
overheating.

NOTE:

The engine can be started after it shuts off.

ESU04701

Throttle override system (T.O.R.S.)

If the throttle bodies or throttle cable malfunctions during
operation, the T.O.R.S. will operate when the throttle
lever is released.
The T.O.R.S. is designed to interrupt the fuel injection
and keep the engine speed between 2,800 and
3,000 r/min if the throttle valves fail to return to the idle
position when the throttle lever is released.

WARNING

@

●

If the T.O.R.S. is activated, make sure that the
cause of the malfunction has been corrected and
that the engine can be operated without a prob-
lem before restarting the engine.

●

Be sure to use the specified spark plug and spark
plug cap. Otherwise, the T.O.R.S. will not work
properly.

@

U8FP10.book Page 2 Thursday, April 28, 2005 5:11 PM

«
...
19
20
21
22
23
...
»

Содержание RX10RL




































































































Отзывы:

Нет отзывов

Похожие инструкции для RX10RL

Бренд: Yamaha Страницы: 282

Safari 377 1988

Бренд: BOMBARDIER Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды