Yamaha RX10RL страница 89 Скачать руководство пользователя

Страница: 89 / 99

9-2

2. Remove the shroud and the right side

cover. (See pages 8-5–8-7 for removal
procedures.)

3. Remove the red (+) connecting lead

from the lead holder and move it away
from the black (-) connecting lead.

CAUTION:

Be sure to connect the red (+) jumper
cable to the red (+) connecting lead and
the black (-) jumper cable to the black (-)
connecting lead. Do not reverse the
connections.

4. Pull the red (+) connecting lead cover

to expose the terminal through the slit
in the cover, and then connect the red
(+) jumper cable to the red (+) connect-
ing lead.

5. Connect the other end of the red (+)

jumper cable to the positive (+) terminal
of the booster battery.

6. Connect the black (-) jumper cable to

the negative (-) terminal of the booster
battery.

7. Pull the black (-) connecting lead cover

to expose the terminal through the slit
in the cover, and then connect the black
(-) jumper cable to the black (-) con-
necting lead.

U8FP10.book Page 2 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды