Yamaha RX10RL Скачать руководство пользователя

Страница: 20 / 99

5-1

ESU00013

CONTROL FUNCTIONS

ESU00362

Main switch

The main switch controls the following items.

“OFF”

The ignition circuit is switched off.
The key can be removed only in this position.

“ON”

The ignition circuit is switched on.

“START”

The starting circuit is switched on.
The starter motor starts.

CAUTION:

Release the switch immediately after the engine
starts.

NOTE:

The headlights, meter lights, and taillights come on after
the engine starts.

ESU00022

Throttle lever

Once the engine is running cleanly, squeezing

the throt-

tle lever

will increase the engine speed and cause

engagement of the drive system. Regulate the speed of
the snowmobile by varying the throttle position. Because
the throttle is spring-loaded, the snowmobile will deceler-
ate, and the engine will return to idle when it is released

WARNING

Check the throttle, brake, and steering for proper
operation before starting the engine.

U8FP10.book Page 1 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды