Yamaha RX10RL Скачать руководство пользователя

Страница: 59 / 99

8-6

Left and right side covers
To remove a side cover

Turn the fasteners counterclockwise, and then remove
the side cover.

Fastener

Right side cover

Left side cover

To install a side cover

Place the side cover in its original position, and then turn
the fasteners clockwise.

NOTE:

Be sure to fit the projection on the rear of the side cover
into the hole in the lower side cover.

Top cover
To remove the top cover

1. Remove the screws, and then remove the cable

guide.

2. Remove the bolts, disconnect the main switch cou-

pler and auxiliary DC jack coupler, and then remove
the top cover.

Screws

Cable guide

Bolts

Top cover

To install the top cover

1. Connect the main switch coupler and auxiliary DC

jack coupler, place the top cover in its original posi-
tion, and then install the bolts.

2. Pass all of the cables, etc., through the cable guide,

place the cable guide in its original position, and then
install the screws.

U8FP10.book Page 6 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды