Yamaha RX10RL Скачать руководство пользователя

Страница: 36 / 99

6-4

CAUTION:

●

When adding the engine oil, be careful not to fill
above the “F” level mark on the oil level
gauge/dipstick.

●

Make sure that no foreign material enters the
engine oil tank.

7. Insert the oil level gauge/dipstick into the oil filler

hole, and then tighten it securely.

8. Connect the oil level gauge coupler.
9. Install the right side cover and the shroud.

ESU04511

Coolant

Checking the coolant level

1. Remove the top cover. (See pages 8-5–8-7 for

removal procedures.)

2. Check the coolant level in the coolant recovery tank

when the engine is cold. If the coolant level is below
the “COLD LEVEL” mark, add soft water until it
reaches the “COLD LEVEL” mark. (See pages 8-14–
8-16 for more details.)

“COLD LEVEL” mark

WARNING

Do not remove the coolant reservoir cap when the
engine is hot.

Coolant reservoir cap

CAUTION:

●

Hard water or salt water is harmful to the engine
parts. You may use boiled or distilled water, if soft
water is not available.

●

Tap water can be used temporarily in an emer-
gency.

U8FP10.book Page 4 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды