Yamaha RX10RL Скачать руководство пользователя

Страница: 41 / 99

6-9

ESU01020

Skis and ski runners

Check the skis and ski runners for wear and damage.
Replace if necessary.

CAUTION:

Avoid scratching the skis when loading and unload-
ing the snowmobile, when riding in areas with little
or no snow, or on sharp edges such as concrete,
curbs, etc. This will wear or damage the skis.

ESU00103

Steering system

Check the handlebar for excessive free play:

1. Push the handlebar up and down and back and forth.
2. Turn the handlebar slightly to the right and left.

If excessive free play is noticed, consult a Yamaha
dealer.

ESU00378

Lights

Check the lights.
Replace any burned out bulbs.

CAUTION:

Avoid using a scraper or hot water for cleaning the
plastic lenses

Ski runner wear limit

8 mm (0.31 in)

Ski wear limit

12 mm (0.47 in)

U8FP10.book Page 9 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды