Yamaha RX10RL страница 72 Скачать руководство пользователя

Страница: 72 / 99

8-19

ESU04611

Checking the drive chain housing oil level and
the drive chain tension

Checking the oil level

WARNING

The engine, oil tank, brake disc, and coolant hoses
will be very hot after the engine has been run. Avoid
contact while they are still hot with any part of your
body or clothing during inspection or repair.

1. Place the snowmobile on a level surface.
2. Remove the shroud and the right side cover. (See

pages 8-5–8-7 for removal procedures.)

3. Remove the dipstick

, wipe it off with a clean rag,

and then insert it back into the filler hole.

4. Remove the dipstick and check that the oil is between

the maximum and minimum level marks. If the oil is
below the minimum level mark, add sufficient oil to
raise it to the maximum level mark.

Maximum level mark

Minimum level mark

For models without reverse transmissions (RX10RT)

For models with reverse transmissions
(RX10R/RX10RTR/RXW10)

CAUTION:

Make sure that no foreign material enters the drive
chain housing.

5. Install the dipstick, making sure to align the notch

in the dipstick handle with the projection

on the

drive chain housing.

6. Install the right side cover and the shroud.

Drive chain oil: GL-3

75W or 80W

U8FP10.book Page 19 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды