Yamaha RX10RL Скачать руководство пользователя

Страница: 79 / 99

8-26

ESU04680

Adjusting the control rod

The weight transfer can be adjusted by turning the con-
trol rod adjuster or adjusting nut.

1. Loosen the locknut

2. Turn the control rod adjuster

in direction

increase weight transfer or direction

to decrease

weight transfer.

CD-27E

3. Check the adjuster length

using the scale on the

special wrench

included in the owner’s tool kit as

shown. Make sure that the rim

of the control rod

body is within the range

of the scale.

4. Tighten the locknut while holding the adjuster in

place.

CAUTION:

When using the special wrench, make sure that it is
situated at a right angle to the control rod, and that it
is tightly fitted to the locknut or the control rod
adjuster.

WARNING

Never adjust the control rod beyond the range of the
scale on the special wrench.

Adjuster turning
direction

←

→

Weight transfer

Increased

←

→

Decreased

Locknut tightening torque:

35 Nm (3.5 m·kgf, 25 ft·lb)

U8FP10.book Page 26 Thursday, April 28, 2005 5:11 PM

Содержание RX10RL




































































































Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды

Yamaha RX10RL, Руководство пользователя

Результаты поиска

Содержание RX10RL

Отзывы:

Похожие инструкции для RX10RL

Бренды по названию

Популярные бренды