Yamaha F9.92 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 94

background image

Maintenance

66

EMU29162

Checking power trim and tilt / power
tilt system

WARNING

EWM00430

●

Never get under the lower unit while it
is tilted, even when the tilt support lever
is locked. Severe injury could occur if
the outboard motor accidentally falls.

●

Make sure no one is under the outboard

motor before performing this test.

1.

Check the power trim and tilt unit / the
power tilt unit for any sign of oil leaks.

2.

Operate each of the power trim and tilt
switches / the power tilt switches on the
remote control and engine bottom cowl-
ing (if equipped) to check that all switch-
es work.

3.

Tilt the outboard motor up and check
that the trim and tilt rod / the tilt rod is
pushed out completely.

4.

Check that the trim and tilt rod / the tilt
rod is free of corrosion or other flaws.

5.

Tilt the outboard motor down. Check
that the trim and tilt rod / the tilt rod oper-
ates smoothly.

NOTE:

Consult your Yamaha dealer if any operation

is abnormal.

EMU29171

Checking propeller

WARNING

EWM00321

You could be seriously injured if the en-
gine accidentally starts when you are
near the propeller.

●

Before inspecting, removing, or install-
ing the propeller, remove the spark
plug caps from the spark plugs. Also,
place the shift control in neutral, turn
the main switch to “

” (off) and re-

move the key, and remove the lanyard
from the engine stop switch. Turn off
the battery cut-off switch if your boat
has one.

●

Do not use your hand to hold the pro-
peller when loosening or tightening the
propeller nut. Put a wood block be-
tween the anti-cavitation plate and the
propeller to prevent the propeller from

turning.

1. Tilt rod

ZMU02059

«
...
70
71
72
73
74
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: MINN KOTA Страницы: 14

Бренд: IEI Technology Страницы: 17

Бренд: JETWAY Страницы: 58

WAFER-CV-N26001

Бренд: IEI Technology Страницы: 135

PX845EV1 Series

Бренд: Albatron Страницы: 56

Бренд: IEI Technology Страницы: 162

Бренд: BCM Страницы: 3

Бренд: Silicon Laboratories Страницы: 9

Бренд: Kontron Страницы: 105

Бренд: Supero Страницы: 105

Memorator Pro 2xHS v2 CB

Бренд: Kvaser Страницы: 22

Бренд: DG Страницы: 18

Бренд: ADLINK Technology Страницы: 67

970A-G43 Series

Бренд: MSI Страницы: 192

Бренд: MSI Страницы: 55

Z75A-GD55 series

Бренд: MSI Страницы: 90

Z77A-G43 GAMING

Бренд: MSI Страницы: 164

Z370 GAMING PRO CARBON

Бренд: MSI Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды