Yamaha F9.92 Скачать руководство пользователя страница 78 | Manualshive

Страница: 78 / 94

background image

Maintenance

72

followed by milk of magnesia, beaten
egg, or vegetable oil. Get immediate
medical attention.

Batteries also generate explosive hydro-
gen gas; therefore, you should always
follow these preventive measures:

●

Charge batteries in a well-ventilated ar-
ea.

●

Keep batteries away from fire, sparks,
or open flames (for example: welding
equipment, lighted cigarettes, and so
on.)

●

DO NOT SMOKE when charging or han-
dling batteries.

KEEP BATTERIES AND ELECTROLYTIC

FLUID OUT OF REACH OF CHILDREN.

CAUTION:

ECM00360

●

A poorly maintained battery will quickly
deteriorate.

●

Ordinary tap water contains minerals
harmful to a battery, and should not be

used for topping up.

1.

Check the electrolyte level at least once
a month. Fill to the manufacturer’s rec-
ommended level when necessary. Top
up only with distilled water (or pure de-
ionized water suitable to use in batter-
ies).

2.

Always keep the battery in a good state

of charge. Installing a voltmeter will help
you monitor your battery. If you will not
use the boat for a month or more, re-
move the battery from the boat and store
it in a cool, dark place. Completely re-
charge the battery before using it.

3.

If the battery will be stored for longer
than a month, check the specific gravity
of the fluid at least once a month and re-
charge the battery when it is low.

NOTE:

Consult a Yamaha dealer when charging or

re-charging batteries.

EMU29331

Connecting the battery

WARNING

EWM00570

Mount the battery holder securely in a
dry, well-ventilated, vibration-free loca-
tion in the boat. Install a fully charged bat-

tery in the holder.

CAUTION:

ECM01121

●

Make sure the main switch (on applica-
ble models) is “

” (off) before work-

ing on the battery.

●

Reversal of the battery cables will dam-
age the electrical parts.

●

Connect the red battery cable first
when installing the battery and discon-
nect the black battery cable first when
removing it. Otherwise, the electrical
parts can be damaged.

●

The electrical contacts of the battery
and cables must be clean and properly
connected, or the battery will not start

the engine.

Connect the red battery cable to the POSI-
TIVE (+) terminal first. Then connect the
black battery cable to the NEGATIVE (-) ter-

«
...
76
77
78
79
80
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Intel Страницы: 78

Бренд: Digital Equipment Страницы: 98

KEEX-1850 Series

Бренд: Quanmax Страницы: 61

Бренд: IDT Страницы: 35

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: Vector Страницы: 73

Бренд: Microchip Technology Страницы: 35

Бренд: Texas Instruments Страницы: 19

Бренд: Supermicro Страницы: 93

EV MOD CH101-01-02

Бренд: TDK Страницы: 10

Бренд: Raisonance Страницы: 46

Бренд: Octek Страницы: 84

Бренд: Zeal-All Страницы: 8

STEVAL-IHM011V1

Бренд: ST Страницы: 27

Бренд: ON Semiconductor Страницы: 5

Бренд: DFI Страницы: 144

Бренд: A-Trend Страницы: 49

Бренд: Humandata Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды