Yamaha F9.92 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 94

background image

Operation

38

ping the engine immediately after operating
at high speed is not recommended.

EMU27844

Procedure

1.

Push and hold the engine stop button or
turn the main switch to “

” (off).

2.

After stopping the engine, disconnect
the fuel line if there is a fuel joint on the
outboard motor.

3.

Tighten the air vent screw on the fuel
tank cap (if equipped).

4.

Remove the key if the boat will be left
unattended.

NOTE:

The engine can also be stopped by pulling
the lanyard and removing the lock plate from
the engine stop switch, then turning the main

switch to “

” (off).

EMU27861

Trimming outboard motor

The trim angle of the outboard motor helps
determine the position of the bow of the boat
in the water. Correct trim angle will help im-
prove performance and fuel economy while
reducing strain on the engine. Correct trim
angle depends upon the combination of
boat, engine, and propeller. Correct trim is
also affected by variables such as the load in
the boat, sea conditions, and running speed.

WARNING

EWM00740

Excessive trim for the operating condi-
tions (either trim up or trim down) can
cause boat instability and can make
steering the boat more difficult. This in-
creases the possibility of an accident. If
the boat begins to feel unstable or is hard
to steer, slow down and/or readjust the

trim angle.

ZMU02083

ZMU02042

ZMU02041

«
...
42
43
44
45
46
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: IEI Technology Страницы: 211

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 8

Бренд: JETWAY Страницы: 46

Бренд: Texas Instruments Страницы: 22

Бренд: Beck Страницы: 24

Бренд: AMPTRON Страницы: 16

Бренд: Texas Instruments Страницы: 14

PENTIUM PRO W6-LI

Бренд: Micronics Страницы: 82

Бренд: IEI Technology Страницы: 153

Бренд: IDT Страницы: 35

LPC1768-Xplorer

Бренд: NGX Technologies Страницы: 25

Бренд: Texas Instruments Страницы: 20

Бренд: MSI Страницы: 90

Бренд: Texas Instruments Страницы: 21

Бренд: Seanix Страницы: 54

Бренд: DFI Страницы: 109

Бренд: Gigabyte Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды