Yamaha F9.92 Скачать руководство пользователя страница 74

Страница: 74 / 94

Maintenance

Remove the propeller nut and washer.

Remove the deflector, propeller, and
thrust washer.

EMU30670

Installing the Propeller

EMU29231

Spline models

CAUTION:

ECM00340

●

Be sure to install the thrust washer be-
fore installing the propeller, otherwise
the lower case and propeller boss
could be damaged.

●

Be sure to use a new cotter pin and
bend the ends over securely. Otherwise
the propeller could come off during op-

eration and be lost.

Apply Yamaha marine grease or a cor-
rosion resistant grease to the propeller
shaft.

Install the spacer (if equipped), thrust
washer, and propeller on the propeller
shaft.

Install the spacer (if equipped) and the
washer. Tighten the propeller nut to the
specified torque.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

NOTE:

If the propeller nut does not align with the
propeller shaft hole after tightening to the
specified torque, tighten the nut further to

align it with the hole.

EMU29262

Dual thrust models

CAUTION:

ECM00340

●

Be sure to install the thrust washer be-
fore installing the propeller, otherwise
the lower case and propeller boss
could be damaged.

●

Be sure to use a new cotter pin and
bend the ends over securely. Otherwise
the propeller could come off during op-

eration and be lost.

Apply Yamaha marine grease or a cor-
rosion resistant grease to the propeller
shaft.

Install the thrust washer and propeller
on the propeller shaft. Install the deflec-
tor on the propeller.

Install the washer and tighten the pro-
peller nut to the specified torque.

Align the propeller nut with the propeller
shaft hole. Insert a new cotter pin in the
hole and bend the cotter pin ends.

3. Washer
4. Deflector
5. Propeller
6. Thrust washer

ZMU02063

Содержание F9.92































































































Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды

Yamaha F9.92, Руководство пользователя

Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды