Yamaha F9.92 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 94

background image

Basic components

17

EMU25970

Throttle friction adjuster

A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.

WARNING

EWM00030

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move throttle lever or grip,

which could result in an accident.

When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.

EMU25990

Engine stop lanyard switch

The lock plate must be attached to the en-
gine stop switch for the engine to run. The
lanyard should be attached to a secure place
on the operator’s clothing, or arm or leg.
Should the operator fall overboard or leave
the helm, the lanyard will pull out the lock
plate, stopping ignition to the engine. This
will prevent the boat from running away un-
der power.

WARNING

EWM00120

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the

boat to be thrown forward.

1. Throttle indicator

ZMU02000

1

ZMU02001

«
...
21
22
23
24
25
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Acrosser Technology Страницы: 7

Бренд: Texas Instruments Страницы: 8

Бренд: EPOX Страницы: 84

Бренд: Biostar Страницы: 118

Бренд: Caji Страницы: 19

Бренд: Gigabyte Страницы: 44

Бренд: Supero Страницы: 85

Qseven conga-QA5

Бренд: Congatec Страницы: 61

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 84

GA-B150M-D3V DDR3

Бренд: Gigabyte Страницы: 4

Бренд: Daewoo Страницы: 39

Бренд: Gigabyte Страницы: 53

Бренд: Supermicro Страницы: 119

Бренд: AZZA Страницы: 61

Бренд: ASROCK Страницы: 5

Бренд: DFI Страницы: 79

Бренд: Foxconn Страницы: 115

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды