Yamaha F9.92 Скачать руководство пользователя страница 53

Страница: 53 / 94

Operation

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28191

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 51.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
(not available for some models) if you use
the outboard motor in turbid (muddy) water
conditions.

ZMU03525

ZMU01988

ZMU01935

ZMU02823

ZMU04900

Содержание F9.92































































































Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды

Yamaha F9.92, Руководство пользователя

Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды