Yamaha F9.92 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 94

background image

General information

10

EMU25690

Battery requirement

CAUTION:

ECM01060

Do not use a battery that does not meet
the specified capacity. If a battery which
does not meet specifications is used, the
electric system could perform poorly or
be overloaded, causing electric system

damage.

For electric start models, choose a battery
which meets the following specifications.

EMU25711

Battery specifications

EMU25730

Without a rectifier or Rectifier
Regulator

CAUTION:

ECM01090

A battery cannot be connected to models
that do not have a rectifier or Rectifier

Regulator.

If you wish to use a battery with the models
without a rectifier or Rectifier Regulator, in-
stall an optional Rectifier Regulator.
Using a maintenance-free battery with the
above models can shorten the life of the bat-
tery significantly.
Install an optional Rectifier Regulator or use

ZMU01710

Minimum cold cranking amps (CCA/
SAE):

F15EH 245.0 A
F15PH 245.0 A
F15PR 245.0 A
F9.9ER2 245.0 A
T9.9EH2 245.0 A
T9.9ER2 245.0 A

Minimum marine cranking amps (MCA/
ABYC):

F15EH 323.0 A
F15PH 323.0 A
F15PR 323.0 A
F9.9ER2 323.0 A
T9.9EH2 323.0 A
T9.9ER2 323.0 A

Minimum reserve capacity (RC/SAE):

F15EH 52 minutes
F15PH 52 minutes
F15PR 52 minutes
F9.9ER2 52 minutes
T9.9EH2 52 minutes
T9.9ER2 52 minutes

«
...
14
15
16
17
18
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: NXP Semiconductors Страницы: 28

Бренд: NXP Semiconductors Страницы: 16

Бренд: ST Страницы: 13

MEG X570S UNIFY-X MAX

Бренд: MSI Страницы: 204

Бренд: Avalue Technology Страницы: 116

tKINO-AL-E1-R10

Бренд: IEI Technology Страницы: 12

Бренд: Gigabyte Страницы: 112

KINO-CV-KINO-CV-N26001

Бренд: IEI Technology Страницы: 164

4Core1600P35-WiFi

Бренд: ASROCK Страницы: 209

RouterBOARD 500r5 Series

Бренд: MikroTik Страницы: 14

Бренд: Abit Страницы: 72

Бренд: AOpen Страницы: 8

Бренд: AOpen Страницы: 97

Бренд: AOpen Страницы: 99

Бренд: AOpen Страницы: 106

Бренд: AOpen Страницы: 125

Бренд: JETWAY Страницы: 47

Бренд: JETWAY Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды