Yamaha F9.92 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 94

background image

Maintenance

65

5.

Start the engine and watch to make sure
the low oil pressure warning indicator (if
equipped) turns off. Make sure that
there are no oil leaks.

CAUTION:

ECM00680

If the low oil pressure warning indicator
does not turn off or if there are oil leaks,
stop the engine and find the cause. Con-
tinued operation with a problem could
cause severe engine damage. Consult
your Yamaha dealer if the problem can-

not be located and corrected.

6.

Turn off the engine and wait 3 minutes.
Recheck the oil level using the dipstick
to be sure the level falls between the up-
per and lower marks. Fill with oil if it is
below the lower mark, or drain to the
specified level if it is above the upper
mark.

7.

Dispose of used oil according to local
regulations.

NOTE:

●

For more information on the disposal of
used oil, consult your Yamaha dealer.

●

Change the oil more often when operating
the engine under adverse conditions such

as extended trolling.

EMU29112

Checking wiring and connectors

●

Check that each grounding wire is properly
secured.

●

Check that each connector is engaged se-
curely.

EMU29120

Exhaust leakage

Start the engine and check that no exhaust
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29130

Water leakage

Start the engine and check that no water
leaks from the joints between the exhaust
cover, cylinder head, and body cylinder.

EMU29140

Engine oil leakage

Check for oil leaks on the around the engine.

NOTE:

If any leaks are found, consult your Yamaha

dealer.

ZMU02057

ZMU02058

ZMU02087

«
...
69
70
71
72
73
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Beck Страницы: 24

Бренд: Gigabyte Страницы: 36

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: JETWAY Страницы: 46

PENTIUM PRO W6-LI

Бренд: Micronics Страницы: 82

BaseTravel 401 S

Бренд: Torqeedo Страницы: 32

8A 72QFN Series

Бренд: IDT Страницы: 29

Бренд: Renesas Страницы: 6

Бренд: Acorp Страницы: 71

Бренд: DFI Страницы: 101

Бренд: Avalue Technology Страницы: 39

Бренд: Avalue Technology Страницы: 54

Бренд: Avalue Technology Страницы: 81

Бренд: Altera Страницы: 6

Бренд: Quantum Research Group Страницы: 15

Бренд: Abit Страницы: 56

Бренд: TYAN Страницы: 23

ALIVENF5-ESATA2

Бренд: ASROCK Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды