Yamaha F9.92 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 94

background image

General information

9

dry rags.

●

Do not overfill the fuel tank.

●

Tighten the filler cap securely after re-
fueling.

●

If you should swallow some gasoline,
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.

●

If any gasoline spills onto your skin, im-
mediately wash with soap and water.
Change clothing if gasoline spills on it.

●

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electro-

static sparks.

CAUTION:

ECM00010

Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign mat-

ter.

EMU25570

Gasoline

If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol and that containing metha-
nol. Gasohol containing ethanol can be used
if ethanol content does not exceed 10% and
the fuel meets minimum octane ratings.
Yamaha does not recommended gasohol
containing methanol because it can cause
fuel system damage or engine performance
problems.

EMU25683

Engine oil

NOTE:

If the recommended engine oil grades are
not available, select an alternative from the
following chart according to the average

temperatures in your area.

CAUTION:

ECM01050

All 4-stroke engines are shipped from the

factory without engine oil.

Recommended gasoline:

Regular unleaded gasoline with a min-
imum octane rating of 86 (Pump Oc-
tane Number) = (R+M)/2

Recommended engine oil:

4-stroke motor oil with a combination
of the following SAE and API oil classi-
fications

Engine oil type SAE:

10W-30 or 10W-40

Engine oil grade API:

SE, SF, SG, SH, SJ, SL

Engine oil quantity (excluding oil filter):

1.0 L (1.06 US qt) (0.88 Imp.qt)

«
...
13
14
15
16
17
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Biostar Страницы: 53

Бренд: Safran Страницы: 26

Бренд: AOpen Страницы: 8

Бренд: Sleipner Страницы: 28

Бренд: ST Страницы: 22

Бренд: MSI Страницы: 30

Бренд: BiPOM Electronics Страницы: 12

CrossLink LIF-MD6000 Master Link Board - Revision C

Бренд: Lattice Страницы: 40

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

Бренд: Gigabyte Страницы: 112

Бренд: Texas Instruments Страницы: 17

Бренд: Gigabyte Страницы: 104

MT9V113PACSTCH-GEVB

Бренд: ON Semiconductor Страницы: 5

H97M Anniversary

Бренд: ASROCK Страницы: 152

Бренд: Gigabyte Страницы: 88

Бренд: Gigabyte Страницы: 120

Бренд: ECS Страницы: 71

Бренд: J&W Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды