Yamaha F9.92 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 94

background image

Trouble Recovery

80

7.

Insert the knotted end of the emergency
starter rope into the notch in the flywheel
rotor and wind the rope around the fly-
wheel several turns clockwise.

8.

Pull the rope slowly until resistance is
felt.

9.

Give a strong pull straight out to crank
and start the engine. Repeat if neces-
sary.

EMU29760

Treatment of submerged motor

If the outboard motor is submerged, immedi-
ately take it to a Yamaha dealer. Otherwise
some corrosion may begin almost immedi-
ately.
If you cannot immediately take the outboard
motor to a Yamaha dealer, follow the proce-
dure below in order to minimize engine dam-
age.

EMU29783

Procedure

1.

Thoroughly wash away mud, salt, sea-
weed, and so on, with fresh water.

2.

Remove the spark plug(s), then face the
spark plug holes downward to allow any
water, mud, or contaminants to drain.

3.

Drain the fuel from the carburetor, fuel
filter, and fuel line. Drain the engine oil
completely.

4.

Fill the sump with the fresh engine oil.

5.

Feed engine fogging oil or engine oil
through the carburetor(s) and spark plug
holes while cranking the engine with the
manual starter or emergency starter
rope.

6.

Take the outboard motor to a Yamaha
dealer as soon as possible.

CAUTION:

ECM00400

Do not attempt to run the outboard motor

until it has been completely inspected.

ZMU02333

ZMU02074

Engine oil capacity:

1.0 L (1.06 US qt) (0.88 Imp.qt)

«
...
84
85
86
87
88
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Ublox Страницы: 23

Бренд: MSI Страницы: 61

Бренд: JETWAY Страницы: 41

Бренд: Procomp Страницы: 55

Бренд: ASROCK Rack Страницы: 83

Бренд: Atmel Страницы: 39

Бренд: Gigabyte Страницы: 37

Бренд: OLIMEX Страницы: 26

Бренд: Foxconn Страницы: 108

ConnectCore 6UL SBC Pro

Бренд: Digi Страницы: 54

Бренд: Ebyte Страницы: 9

XtremeDSP Spartan-3A DSP 3400A...

Бренд: Xilinx Страницы: 50

Бренд: ST Страницы: 47

Бренд: DataExpert Страницы: 44

Бренд: Suzuki Marine Страницы: 63

Бренд: Terra Страницы: 6

Бренд: Altera Страницы: 144

Бренд: Abit Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды