Yamaha F9.92 Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 94

background image

Basic components

20

switch, see pages 38 and 41.

EMU26110

Steering friction adjuster

A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
juster lever is located on the bottom of the
tiller handle bracket.
To increase resistance, turn the lever to the
left.
To decrease resistance, turn the lever to the
right.

WARNING

EWM00040

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an

accident.

EMU26122

Steering friction adjuster

A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
justing screw or bolt is located on the swivel
bracket.

To increase resistance, turn the adjuster
clockwise.
To decrease resistance, turn the adjuster
counterclockwise.

WARNING

EWM00040

Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an

accident.

EMU26241

Trim tab with anode

The trim tab should be adjusted so that the
steering control can be turned to either the
right or left by applying the same amount of
force.

WARNING

EWM00840

An improperly adjusted trim tab could
cause difficult steering. Always test run
after the trim tab has been installed or re-
placed to be sure steering is correct. Be
sure you have tightened the bolt after ad-

justing the trim tab.

If the boat tends to veer the left (port side),
turn the trim tab rear end to the port side “A”
in the figure. If the boat tends to veer the right
(starboard side), turn the trim tab end to the

ZMU02340

ZMU02080

«
...
24
25
26
27
28
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Navia Страницы: 26

SuperServer SYS-E102-9AP-LN4-C

Бренд: Supermicro Страницы: 81

Бренд: BESTEK Страницы: 52

Бренд: DAQ system Страницы: 52

Бренд: Gigabyte Страницы: 40

Бренд: DFI Страницы: 44

Бренд: Gigabyte Страницы: 38

Бренд: Biostar Страницы: 32

Бренд: Systium Technologies Страницы: 4

Бренд: Semtech Страницы: 16

25 Jet FourStroke

Бренд: Mercury Страницы: 110

CAES UT65CML8X8FD-EVB-UM

Бренд: COBHAM Страницы: 20

Бренд: Pericom Страницы: 8

Бренд: JETWAY Страницы: 48

Бренд: Texas Instruments Страницы: 28

Бренд: Advantech Страницы: 84

Бренд: Biostar Страницы: 60

Бренд: Microchip Technology Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды