Yamaha F9.92 Скачать руководство пользователя страница 42

Страница: 42 / 94

Operation

you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the

engine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

Move the gear shift lever quickly and
firmly from neutral to forward.

Remote control models
1.

Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from neutral to
forward.

EMU27795

Reverse (manual tilt and hydro tilt
models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and

an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

ZMU02030

ZMU02036

ZMU04882

Содержание F9.92































































































Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды

Yamaha F9.92, Руководство пользователя

Результаты поиска

Содержание F9.92

Отзывы:

Похожие инструкции для F9.92

Бренды по названию

Популярные бренды