Yamaha F9.92 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 94

background image

Operation

31

NOTE:

●

It is not necessary to use the choke when
starting a warm engine.

●

If the choke knob is left in the “

”

(start) position while the engine is running,

the engine will run poorly or stall.

5.

Pull the manual starter handle slowly un-
til you feel resistance. Then give a
strong pull straight out to crank and start
the engine. Repeat if necessary.

6.

After the engine starts, slowly return the
manual starter handle to its original po-
sition before releasing it.

7.

Slowly return the throttle grip to the fully
closed position.

NOTE:

●

When the engine is cold, it needs to be
warmed up. For further information, see
page 35.

●

If the engine does not start on the first try,
repeat the procedure. If the engine fails to
start after 4 or 5 tries, open the throttle a
small amount (between 1/8 and 1/4) and
try again. Also if the engine is warm and
fails to start, open the throttle a same
amount and try to start the engine again. If

the engine still fails to start, see page 74.

EMU27562

Electric start models

1.

Place the gear shift lever in neutral.

ZMU02355

ZMU02029

ZMU02030

ZMU01988

N

«
...
35
36
37
38
39
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: Lantronix Страницы: 10

Бренд: JETWAY Страницы: 18

Бренд: J&W Страницы: 37

Бренд: ECS Страницы: 52

Бренд: Variscite Страницы: 2

Бренд: Raider Outboards Страницы: 73

Бренд: JETWAY Страницы: 56

Бренд: Texas Instruments Страницы: 24

Бренд: Texas Instruments Страницы: 14

Бренд: Dynatem Страницы: 57

Бренд: Intel Страницы: 36

LMQ61460EVM-400K

Бренд: Texas Instruments Страницы: 20

Бренд: IEI Technology Страницы: 161

Бренд: ESC Страницы: 56

Бренд: ASROCK Rack Страницы: 83

Бренд: ASROCK Rack Страницы: 83

Бренд: Redpine Signals Страницы: 79

Taichi Razer Edition X570

Бренд: ASROCK Страницы: 254

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды