Yamaha F9.92 Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 94

background image

Operation

32

NOTE:

The start-in-gear protection device prevents
the engine from starting except when in neu-

tral.

2.

Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg. Then install the lock plate on
the other end of the lanyard into the en-
gine stop switch.

WARNING

EWM00120

●

Attach the engine stop switch lanyard
to a secure place on your clothing, or
your arm or leg while operating.

●

Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.

●

Avoid accidentally pulling the lanyard
during normal operation. Loss of en-
gine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly. This
could cause people and objects in the

boat to be thrown forward.

3.

Place the throttle grip in the “

”

(start) position. After the engine starts,
return the throttle to the fully closed po-
sition.

4.

Pull out / turn the choke knob fully. After
the engine starts, replace / return the
knob to the home position.

NOTE:

●

It is not necessary to use the choke when
starting a warm engine.

N

ZMU04881

ZMU02026

ZMU02027

ZMU02355

«
...
36
37
38
39
40
...
»

Содержание F9.92































































































Отзывы:

Нет отзывов

Похожие инструкции для F9.92

Бренд: IBASE Technology Страницы: 33

Бренд: M5Stack Страницы: 16

Бренд: Udoo Страницы: 9

KT333 DRAGON Plus

Бренд: SOYO Страницы: 34

Бренд: SOLTEK Страницы: 72

Бренд: Intel Страницы: 97

Бренд: Gigabyte Страницы: 31

Бренд: Raptor Страницы: 59

Бренд: Texas Instruments Страницы: 21

Бренд: ASROCK Rack Страницы: 93

Бренд: TransCore Страницы: 40

VVDI Mini Key Tool

Бренд: Xhorse Страницы: 17

Бренд: Ublox Страницы: 22

Бренд: JETWAY Страницы: 57

AR6MXCS- Series

Бренд: BCM Страницы: 9

Бренд: Aaeon Страницы: 78

Бренд: Zamel Страницы: 3

BLKD955XBKLKR - 10PK 955X LGA775 8GB DDR2 16X

Бренд: Intel Страницы: 94

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды