Yaesu FTDX-9000MP, Руководство по эксплуатации

Страница: 36 / 180

Page 34 FT
DX
9000MP O
PERATION
M
ANUAL
VDD TEMP SWR BIAS
MCH/GRP Switch
MCH Switch
Pressing this button momentarily allows you to select
the memory channel using the [
CLAR/VFO-B
] knob
(# , described later).
GRP Switch
Pressing and holding in this button for 2 seconds al-
lows you to select the memory group using the [
CLAR/
VFO-B
] knob (#
, described later).
CLAR/VFO-B Knob
Depending on the status of the [ A/B
] switch (#
,
described later) the [ CLAR/VFO-B
] knob is used for
functions associated with the Main (VFO-A) or Sub
(VFO-B) frequency control registers.
FAST/RX Switch
FAST Switch
When the [ A/B
] switch (#
, described later) is
pushed, and the Umber lamp to the right of the [ CLAR/
VFO-B
] knob (#
, described previously) lights up,
the [ CLAR/VFO-B
] knob will be controlling the Sub
(VFO-B) frequency; pressing the [ FAST/RX
] switch
will change the tuning step of the [ CLAR/VFO-B
]
knob to 100 Hz.
RX Switch
When the [ CLAR
] switch (#
, described previously)
is pressed (and its imbedded LED is illuminated),
pressing the [
FAST/RX
] switch applies the pro-
grammed Clarifier offset to the Main (VFO-A) receive
frequency. Press the [
FAST/RX
] switch once more to
return the Main receiver to the frequency shown on
the main frequency display field; the Clarifier offset
will still be present, though, in case you want to use it
again. To cancel the Clarifier offset, press the
[
B.MODE/CLEAR
] switch (see details in #
be-
low).
FFFFF
RRRRRONT ONT
ONT ONT
ONT
P P P P P
ANEL ANEL
ANEL ANEL
ANEL
C C C C C
ONTR ONTR
ONTR ONTR
ONTROLS OLS
OLS OLS
OLS
BAND/MHz / TX Switch
BAND/MHz
When the [ A/B
] switch (#
, described later) is
pressed, and the Orange lamp to the right of the
[
CLAR/VFO-B
] knob (#
, described previously)
lights up, pressing the [ BAND/MHz
] switch allows
you to rotate this knob for selection of the Amateur
band to be used for the Sub band (VFO-B).
TX Switch
When the [ CLAR
] switch (#
, described previously)
is pressed (and its imbedded LED is illuminated),
pressing the [
BAND/MHz / TX
] switch applies the
programmed Clarifier offset to the Main (VFO-A)
transmit frequency. Press the [
FAST/RX
] switch (#
,
described previously) once more to return the trans-
mitter to the Main (VFO-A) frequency shown on the
main frequency display field; the Clarifier offset will
still be present, though, in case you want to use it again.
To cancel the Clarifier offset, press the [
B.MODE/
CLEAR
] switch (see details in #
below).
B.MODE/CLEAR Switch
B.MODE Switch
When the [ A/B
] switch (#
below) is pressed, and
the Orange lamp to the right of the [ CLAR/VFO-B
]
knob (# , described previously) lights up, pressing
the [ B.MODE/CLEAR
] switch allows you to rotate
this knob for selection of the operating mode to be
used on the Sub band (VFO-B).
CLEAR Switch
When the [ CLAR
] switch (#
, described previously)
is pressed (and its imbedded LED is illuminated),
pressing the [
B.MODE/CLEAR
] switch clears out any
frequency offset you have programmed into the Clari-
fier register (thereby setting the offset to “Zero”).