Yaesu FTDX-9000MP, Руководство по эксплуатации

Страница: 165 / 180

Page 163 FT
DX
9000MP O
PERATION
M
ANUAL
167. P-PRMTRC EQ3-FREQ
Function : Selects the center frequency of the high
range for the front panel’s parametric microphone
equalizer when the speech processor is activated.
Available Values : OFF/1500 ~ 3200 Hz (100 Hz/step)
Default Setting : 2100 (Hz)
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
1500 ~ 3200: You may adjust the equalizer gain and
Q-factor in this selected audio fre-
quency via menu items 168:
P- P- P- P- P-
PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL
PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL PRMTRC EQ3-LEVEL and 169:
P- P-
P- P- P-
PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH PRMTRC EQ3-BWTH .
168. P-PRMTRC EQ3-LEVEL
Function : Adjusts the equalizer gain of the high range
of the front panel’s parametric microphone equalizer
when the speech processor is activated.
Available Values : –20 ~ +10
Default Setting : 0
169. P-PRMTRC EQ3-BWTH
Function : Adjusts the Q-factor of the high range of
the front panel’s parametric microphone equalizer
when the speech processor is activated.
Available Values : 1 ~ 10
Default Setting : 1
TX GNRL G
ROUP
170. TX MAX POWER
Function : Selects a maximum output power limit.
Available Values : 400/200/100/50 W
Default Setting : 400 W
171. TX PWR CONTROL
Function : Configures the RF PWR knob.
Available Values : ALL MODE/CARRIER
Default Setting : ALL MODE
ALL MODE: The [ RF PWR
] knob is enabled on all
modes.
CARRIER: The [ RF PWR
] knob is enabled in all
modes except SSB. In this configura-
tion, the SSB output power will be set to
maximum, regardless of the [
RF PWR
]
knob’s position.
172. EXT AMP TX-GND
Function : Enables/Disables the TX GND jack on the
rear panel.
Available Values : ENABLE/DISABLE
Default Setting : DISABLE
173. EXT AMP TUNING PWR
Function : Selects a maximum output power limit for
driving the input circuit of an external linear RF am-
plifier while tuning (while using the Remote Control
function of the linear RF amplifier).
Available Values : 400/200/100/50 W
Default Setting : 100 W
174. FULL DUPLEX
Function : Enables/Disables Full Duplex operation.
Available Values : SIMP/DUP
Default Setting : SIMP
When this menu is set to “DUP,” you may receive on
the sub band (VFO-B) frequency while transmitting,
during dual receive operation, on a different band on
the main band (VFO-A).
175. VOX SELECT
Function : Selects the audio input source for trigger-
ing TX during VOX operation.
Available Values : MIC/DATA
Default Setting : MIC
MIC: The VOX function will be activated by micro-
phone audio input.
DATA: The VOX function will be activated by data
audio input.
176. EMERGENCY FREQ TX
Function : Enables Tx/Rx operation on the Alaska
Emergency Channel, 5167.5 kHz.
Available Values : DISABLE/ENABLE
Default Setting : DISABLE
When this Menu Item is set to “ENABLE,” the spot
frequency of 5167.5 kHz will be enabled. The Alaska
Emergency Channel will be found between the
Memory channels “P-1” and “01 (or 1-01).”
TX AUDIO G
ROUP
MMMMM
ENU ENU
ENU ENU
ENU
M M M M M
ODE ODE
ODE ODE
ODE