Yaesu FTDX-9000MP, Руководство по эксплуатации

Страница: 46 / 180

Page 44 FT
DX
9000MP O
PERATION
M
ANUAL
BBBBB
ASIC ASIC
ASIC ASIC ASIC
O O O O O
PERA PERA
PERA PERA PERATION
TION
TION TION TION
::::: R R R R R
ECEIVING ECEIVING
ECEIVING ECEIVING ECEIVING
ON ON
ON ON ON
AAAAA
MA MA
MA MA MATEUR
TEUR
TEUR TEUR TEUR
B B B B B
ANDS ANDS
ANDS ANDS ANDS
1. Set the FPS-9000H ’s Power switch to “
I
.”
2. Press and hold in the front-panel
[
POWER
] switch for two seconds to turn
the transceiver on.
3. After about 50 seconds, all circuits will
be initialized. the transceiver will start
up on 7.000.00 MHz LSB, and normal
operation may resume.
N N N N N
O O
O O OTE
TE
TE TE TE
:
To turn power off, press and hold in the front panel
[
POWER
] switch for two seconds.
Q Q
Q Q
Q
UICK UICK UICK UICK UICK
N N
N N
N
O O O O OTE TE TE TE TE
:
If the External display is connected, the opening screen
on the External display will be gray, and some text
notes advising status during the boot-up sequence may
appear. When the radio is turned on for the first time,
it takes about 50 seconds (from turning the radio on to
completing the self- check) until the radio becomes
ready to use; however, from the next time you turn it
on, it will take around 10 seconds until the transceiver
is ready for full operation.
4. Rotate the [ AF GAIN
] knob
to set a comfortable audio
level on incoming signals or
noise. Clockwise rotation of
the [
AF GAIN
] knob in-
creases the volume level.
N N
N N
N
O O O O OTE TE TE TE TE
:
When using headphones, start by rotating the [ AF
GAIN
] control counter-clockwise, then bring the vol-
ume level up after you put the headphones on. this
will minimize the chance of damage to your hearing
caused by an unexpectedly-high audio level.
5. Press the [ MAIN RX
] switch to engage the Main
(VFO-A) receiver, the imbeded LED will glow Green.
A A
A A
A
D D
D D DVICE
VICE
VICE VICE VICE
:
If you press the [
MAIN RX
] key when the imbedded
LED is already glowing Green, the LED will now blink
on and off; this indicates that the Main (VFO-A) re-
ceiver is temporarily muted. Just press the [
MAIN RX
]
key once more to restore Main (VFO-A) receiver op-
eration.
Press the [
SUB RX
] switch to engage Dual Recep-
tion (using Sub the (VFO-B) receiver in addition to
the Main (VFO-A) receiver). When you press the
[
SUB RX
] key, its imbedded LED will glow green;
pressing this key once more will turn off the Sub (VFO-
B) receiver, and the impeded LED will glow dark. Use
the Sub Receiver’s [
AF GAIN
] knob to adjust the Sub
(VFO-B) receiver volume level.
6. Press the [
A
] switch to enable the
capability to change the operation for
the Main (VFO-A) band the imbed-
ded LED will glow Red.
7. Press the [
BAND
] key corresponding to the Amateur
band on which you wish to begin operation.
VDD TEMP SWR BIAS
[BAND] Key
[POWER] Switch
Main (VFO-A) [RX] Switch
[MODE] Switch
[CLAR/VFO-B] Knob
[A/B] Switch [BAND/MHz] Switch
[AF GAIN] Knob
A A A A A
D D D D DVICE VICE VICE VICE VICE
:
One-touch selection of each Amateur band be-
tween 1.8 and 50 MHz is provided.
If you press the [
BAND/MHz
] key momentarily,
the [
CLAR/VFO-B
] knob may be used as a band
selection knob. If the
[
CLAR/VFO-B
] knob is
pressed and held in for
two seconds, rotation of
the [
BAND/MHz
] key al-
lows frequency naviga-
tion in 1 MHz steps.
When the [
BAND/MHz
] key’s imbedded LED is
illuminated, the [ CLAR/VFO-B
] knob controls
the functions associated with the [
BAND/MHz
]
key.
Depending on the setting of the [
A/B
] switch, the
function of the [ CLAR/VFO-B
] knob will change.
Please see page 35 for more details.