Yaesu FTDX-9000MP, Руководство по эксплуатации

Страница: 152 / 180

Page 150 FT
DX
9000MP O
PERATION
M
ANUAL
MMMMM
ENU ENU
ENU ENU
ENU
M M M M M
ODE ODE
ODE ODE
ODE
GENERAL G
ROUP
031. ANT SELECT
Function : Sets the method of antenna selection.
Available Values : BAND/STACK
Default Setting : BAND
BAND: The antenna is selected in accordance with
the operating band.
STACK: The antenna is selected in accordance with
the band stack (different antennas may be
utilized on the same band, if so selected in
the band stack).
032. BEEP LEVEL
Function : Sets the beep level.
Available Values : 0 ~ 255
Default Setting : 50
033. CAT RATE
Function : Sets the transceiver’s computer-interface
circuitry for the CAT baud rate to be used.
Available Values : 4800/9600/19200/38400 bps
Default Setting : 4800 bps
034. CAT TIME OUT TIMER
Function : Sets the Time-Out Timer countdown time
for a CAT command input.
Available Values : 10/100/1000/3000 msec
Default Setting : 10 msec
The Time-Out Timer shuts off the CAT data input af-
ter the continuous transmission of the programmed
time.
035. CAT RTS
Function : Enables/Disables the RTS port of the CAT
jack.
Available Values : DISABLE/ENABLE
Default Setting : ENABLE
036. CAT DATA INDICATOR
Function : Enables/Disables the flashing of the Data
LED at the left side of the [ CS
] switch in conjunction
with the CAT commands.
Available Values : DISABLE/ENABLE
Default Setting : ENABLE
037. MEM GROUP
Function : Enables/Disables Memory Group Opera-
tion.
Available Values : DISABLE/ENABLE
Default Setting : DISABLE
039. QUICK SPLIT FREQ
Function : Selects the tuning offset for the Quick Split
feature.
Available Values : –20 ~ 0 ~ +20 kHz (1 kHz Step)
Default Setting : +5 kHz
039. TRACKING
Function : Sets the VFO Tracking feature.
Available Values : OFF / BAND / FREQ
Default Setting : OFF
OFF: Disables the VFO Tracking feature.
BAND: When you change bands on the Main (VFO-
A) side, the Sub (VFO-B) band’s VFO will
automatically change to be the same as that
of VFO-A.
FREQ: This function is the almost same as “BAND,”
however, furthermore, the Sub band’s (VFO-
B) frequency changes together with the Main
band’s (VFO-A) frequency when turning the
Main Dial Tuning knob.
040. TIME OUT TIMER
Function : Sets the Time-Out Timer countdown time.
Available Values : OFF/5/10/15/20/25/30 min
Default Setting : OFF
The Time-Out Timer shuts off the transmitter after
continuous transmission of the programmed time.
041. TRV OFFSET
Function : Set the 10’s and 1’s of the MHz digits dis-
play for operation with a transverter.
Available Values : 30 ~ 49 MHz
Default Setting : 44 MHz
If you connect a 430 MHz transverter to the radio, set
this menu to “30” (the “100 MHz” digits are hidden on
this radio).
042. μ TUNE DIAL STEP
Function : Select the μ -TUNE mode.
Available Values : DIAL STEP-1/DIAL STEP-2/OFF
Default Setting : DIAL STEP-1
DIAL STEP-1: Activates the μ -TUNE system in the
Auto mode using “ FINE ” steps of the
[
μ -TUNE
] knob (1 step/click) on the
14 MHz and lower amateur bands on
the Main band (VFO-A).
DIAL STEP-2: Activates the μ -TUNE system in the
Auto mode using “ COARSE ” steps of
the [ μ -TUNE
] knob (2 steps/click) on
the 7 MHz and lower amateur bands.
On the 10/14 MHz bands,“FINE”
μ -TUNE
knob steps will be used (1 step/click).
OFF: Disables the μ -TUNE system. Acti-
vates the VRF feature on the 14 MHz
and lower amateur bands on the Main
band (VFO-A).
Advice : If none of the RF μ -Tuning Unist is installed,
changing this Menu setting will have no effect.