Network Configuration
WorkCentre 5300 Series Multifunction Printer
System Administrator Guide
25
Zero-Configuration Networking
1.
If the printer cannot connect to a DHCP server to obtain an IP address, select
Self Assigned
Address
to allow the printer to assign itself a Link-Local address. Link-Local addresses are between
169.254.0.0 and 169.254.255.255.
2.
Click
Apply
.
Configuring Settings for IPv6
IPv6 hosts can automatically configure themselves when connected to a routed IPv6 network
using the Internet Control Message Protocol Version 6 (ICMPv6). ICMPv6 performs error reporting
for IP along with other diagnostic functions. When first connected to a network, a host sends a
link-local multicast router solicitation request for its configuration parameters. If suitably configured,
routers respond to this request with a router advertisement packet containing network-layer
configuration parameters.
Note:
IPv6 is optional and may be used in addition to or in place of IPv4. If both protocols are
disabled, you cannot access CentreWare IS.
1.
In CentreWare IS, click
Properties
>
Connectivity
>
Protocols
>
TCP/IP
.
2.
Under
IP Mode
, select
IPv6
, or select
Dual Stack
to use both IPv4 and IPv6. By default, IPv6
is disabled.
CAUTION:
If both IPv4 and IPv6 are disabled, you cannot access CentreWare IS. You must
re-enable TCP/IP at the printer control panel before you can access CentreWare IS. Disabling
TCP/IP or changing the IP address also disables any dependant protocols.
Notes:
•
The host name is the same for IPv4 and IPv6. If you change the host name for IPv6, the
host name changes for IPv4 as well.
•
Enabling or disabling IPv6 will restart the printer when you click
Apply
.
3.
Next to
Enable Manual Address
, select
Enabled
if you want to manually assign an address.
Type the
IP Address
and
Gateway Address
.
4.
Next to
Get IP Address from DHCP
, select
Enabled
to allow your DHCP server to assign an IP
address to the printer.
5.
Type the required
Domain Name
.
DNS Configuration for IPv6
1.
Next to
Obtain IPv6 DNS Server Address Automatically
, select
Enabled
to allow the DHCP
server to provide the DNS server address.
2.
Type an IP address for the
Preferred DNS Server
,
Alternate DNS Server 1
, and
Alternate DNS
Server 2
.
3.
Next to
Dynamic DNS Registration
, select
Enabled
to enable, select
Overwrite
to replace the
existing DNS entry.
4.
Next to
Generate Domain Search List Automatically
, select
Enabled
to enable.
5.
Type
Domain Name
1, 2 and 3.
6.
Enter the number of seconds until
Connection Time-Out
.
Содержание WorkCentre 5320
