![background image](http://html1.mh-extra.com/html/xerox/5915/5915_service-manual_884767033.webp)
2-24
Section 2 Troubleshooting
2.4 level 2 Troubleshooting
U8-1
EXPOSURE CONTROL FAIL
Ref. BSD: 3
Problem Area
: Initial Light Quantity Control(Optics)
Cause/Corrective Action
•
Defective Main PWB
•
Defective AC Drive PWB
•
Open harnesses or improper P/J connections of the circuits
controlling the above PWB’s.
U8-2
NO ZERO CROSS FAIL
Ref. BSD: 7
Preparation
: Ensure that P/J410 of Main PWB is securely
connected to P/J430 of AC Drive PWB.
WARNING:
Hazardous voltage. Use extreme care
.
Procedure
Power on. Detect the zero cross signal.
Is the level from P/J410-9 to COM +0.5VDC?
Y N
Is the voltage from P/J437-1 to P/J437-2 220VAC?
Y N
Check 220VAC input circuit.
Is the Front INTLK switch close?
Is the voltage from J431 to COM +24VDC?
Y N
Check the trouble chain E5.
Check the start signal of the INTLK Power Relay.
Is the level from P/J410-11 to com 0v?
Y N
Replace the Main PWB.
Check the wire from P/J430-4 of AC DRIVER to P/J410-11 of
Main PWB for an open circuit, short circuit or improper
connection. If no problem exists, replace the Main PWB
Replace the Main PWB.
U8-4 EXPOSURE VOLTAGE OVER FAIL
Ref. BSD: 3
Problem Area
: Light Quantity/Voltage Control(Optics)
Procedure
check the wire from P/J430-1 of AC DRIVER to P/J410-10 of Main
PWB.
Power on. Detect the Exposure Sensor Signal level.
Is the level from P/J410-10 to COM over 2.9VDC?
Y N
Replace Main PWB.
Replace AC DRIVER.
U8-5
EXPOSURE LIGHT QTY/VOLTAGE UNDER FAIL
Ref. BSD: 3
Problem Area
: Light Quantity/Voltage Control(Optics)
Preparation
: Ensure that P/J410-10 of Main PWB is securely
connected to P/J430-1 of AC Drive PWB.
Procedure
Enter Diag. Mode. Enter [6-7],[6-8].
Check the A/D value, A5-A7.
Is the voltage from P/J430-1 to COM
≤
0.5V?
Y N
Replace the Main PWB.
Replace the AC DRIVER.
Содержание 5915
