![background image](http://html1.mh-extra.com/html/xerox/5915/5915_service-manual_884767025.webp)
2-16
Section 2 Troubleshooting
2.4 level 2 Troubleshooting
2.4 Level 2 Troubleshooting
2.4.1 General F.I.P (General F.I.P for Defective Parts)
••••
Reflective Sensor F.I.P [SENSED(L)]
ORIGINAL SIZE Sensors 1~4
Preparation
:
•
Remove any remaining paper (if there is any).
Procedure
Enter Diag. [
٭
-
٭
].
Make the Sensor turn ON/OFF with a blank sheet of paper.
Does the display repeat (L) and (H) alternately ?
Y
N
Does the display remain (H)?
Y
N
It remains (L).
Check with the tester the harness from Pin 2 of the
Sensor to Pin 5 of PWB for a short circuit. If it is good,
replace the Sensor.
Can the tester lead wire be inserted in Jxx of the Sensor ?
Y
N
Check Pins 4/5/6 for improper connections or
Harnesses
○
A
○
B
○
C
for open circuits. If they are good,
replace the Sensor.
٭
You can also check by exchanging the Sensor with
another Sensor of the same type if one is available.
Place the tester wire between Pin 2(+) of the Sensor and
COM(–) .
Make the Sensor turn ON/OFF with blank paper.
Does the voltage repeat (L) and (H) alternately?
Y
N
Is the voltage from Pin
1
(+) to Pin 3 of the Sensor
+5VDC?
Y
N
Check Pins 4/6 for improper connections or
Harnesses
○
A
○
C
for open circuits.
Replace the Sensor.
Check to see if the document detecting position on Platen
Glass is contaminated. If not, replace the PWB.
Check outer light/check the sensor for its installation and (signal)
chattering. If no problem exists, replace the PWB.
••••
••••
Permeable Sensor F.I.P [SENSOR(H)]
OTHER SENSORs with 3
Wiring
Preparation
:
•
Remove any remaining paper (if there is any).
Procedure
Enter Diag. [
٭
–
٭
].
Make Actuator turn ON/OFF manually or with paper. (If necessary,
use Output Check.)
Y
N
Does the display remain (H)?
Y
N
It remains (L).
Check with the tester the harness
○
B
from Pin 2 of the
Sensor to Pin 5 of PWB for a short circuit. If it is good,
replace the Sensor.
Can the tester lead wire be inserted in Jxx of the Sensor?
Y
N
Check Pins 4/5/6 for improper connections or
Harnesses
○
A
○
B
○
C
for open circuits. If they are good,
replace the Sensor.
٭
You can also check by exchanging the Sensor with
another Sensor of the same type if one is available.
Place the tester wire between Pin 2(+) of the Sensor and
COM(–) .
Make Actuator turn ON/OFF manually or with paper.
Does the voltage repeat (L) and (H) alternately?
Y
N
Is the voltage from Pin
1
(+) to Pin 3 of the Sensor
+ 5VDC?
Y
N
Check Pins 4/6 for improper connections or
Harnesses
○
A
○
C
for open circuits.
Replace the Sensor.
Replace the PWB.
Check the Sensor for its installation and (signal) chattering. If no
problem exists, replace the PWB.
Содержание 5915
