Ricoh FT8680 Service Manual Download | Manualshive

Page: 1 / 389

background image

IMPORTANT SAFETY NOTICES

PREVENTION OF PHYSICAL INJURY

1. While the machine warms up, it will suddenly start turning to perform the

process control data initialization. Keep hands away from any mechanical
and electrical components during this period.

2. Before disassembling or assembling parts of the copier and peripherals,

make sure that the copier and the second sorter power cord is unplugged.

3. The wall outlet should be near the copier and easily accessible.

4. Note that some components of the copier, the paper tray unit, and the

2nd sorter are supplied with electrical voltage even if the main switch is
turned off.

5. If any adjustment or operation check has to be made with exterior covers

off or open while the main switch is turned on, keep hands away from
electrified or mechanically driven components.

6. The inside and the metal parts of the fusing unit become extremely hot

while the copier is operating. Be careful to avoid touching those
components with your bare hands.

HEALTH SAFETY CONDITIONS

1. Never operate the copier without the ozone filters installed.

2. Always replace the ozone filters with the specified ones at the specified

intervals.

3. Toner and developer are non-toxic, but if you get either of them in your

eyes by accident, it may cause temporary eye discomfort. Try to remove
with eye drops or flush with water as first aid. If unsuccessful, get medical
attention.

1
2
3
...
»

Summary of Contents for FT8680






































































































































































































































































































































































































Reviews:

No comments

Related manuals for FT8680

Brand: Canon Pages: 214

Brand: Lexmark Pages: 259

Brand: Muratec Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands