Xerox 5915, Руководство по обслуживанию, Страница: 24 / 146

2-15 2.3 Level 1 Troubleshooting
Section 2 Troubleshooting
STATUS
CODE
NAME PROBLEM CORRECTIVE ACTION
REF.
BSD
C1-2 TRAY 1 MIS FEED JAM Regi-gate Sensor isn’t turned on within 2.7sec. after paper starts to be fed.
•
Refer to the MISFEED JAM.
4
C9-3 MSI MISFEED JAM Regi-gate Sensor isn’t turned on within 2.3 sec. after paper starts to be fed.
•
Refer to the MISFEED JAM 4
E1-1 FUSER EXIT SWITCH ON CHECK JAM Fuser Exit Switch isn’t turned on within 3.7 sec. After Regi-Gate is open.
•
Refer to BSD Sheet 5 5
E1-2 REGI-GATE SENSOR OFF CHECK JAM
Regi-Gate Sensor isn’t turned off (remains ON) a preset period of time (which varies with paper
sizes) after Regi-Gate is open.
•
Refer to BSD Sheet 5 5
E1-6 REGI-GATE SENSOR STATIC JAM Regi-Sensor is on during Power On or Stand-by. (Paper remains)
•
Remove the paper
•
Check the Regi-Gate sensor circuit.
4
E3-3 FUSER EXIT SWITCH OFF CHECK JAM
Fuser Exit isn’t turned off (remains ON) a preset period of time (which varies with paper sizes) after
Fuser Exit Switch is turned on.
•
Refer to BSD Sheet 5 5
E3-6 FUSER EXIT SWITCH STATIC JAM Fuser Exit Switch is on during Power On or Stand-by. (Paper remains)
•
Remove the paper
•
Check the Fuser Exit Switch circuit.
5
E5-1 FRONT INTLK OPEN FAIL Front Cover is open, or Front Interlock Switch is defective.
•
Close Front Cover.
•
Check the Front Interlock Switch circuit.
4
E6-1 R/H UPPER INTLK OPEN FAIL R/H Upper Cover is open, or R/H Upper Interlock Switch is defective.
•
Check R/H Upper Cover.
•
Check the R/H Upper Interlock switch circuit.
4
J1-1 TONER EMPTY FAIL Number of copies reaches 100 after toner empty sensor sensed toner end condition.
•
Supply toner.
•
Check the Toner Empty Sensor circuit.
5
J1-2 TONER LIFE END The counter value of toner unit reaches the default value 7700.
•
Replace the Toner Cartridge. 5
J3-1 DRUM UNIT SET FAIL Drum unit is not set, or is set incorrectly to the machine.
•
Ensure to install the Drum Unit to the machine
properly
5
J3-2 Toner Cartridge SET FAIL Toner unit is not set, or is set incorrectly to the machine.
•
Ensure to install the Toner Unit to the machine
properly
5
J3-3 Counter SET FAIL Total counter is corrected improperly.
•
Ensure to install the Total Copy Count Unit to
the machine
5
J6-1 DRUM UNIT ID FAIL Drum unit Read/Write is in error.
•
Replace the Drum Unit. 5
J6-2 Toner Cartridge ID FAIL Toner unit Read/Write is in error.
•
Replace the Toner Unit. 5
J6-3 Counter ID FAIL Total Counter Read/Write is in error.
•
Replace the Total Copy Count Unit. 5
J7-1 DRUM UNIT LIFE END Copy Value has become 50K (sheets of paper)
•
Replace the Drum Unit. 5
J8-1 DRUM UNIT TYPE NO. FAIL Type No. stored in ID of Drum Unit is not the same as that stored in NVM of the Main PWB.
•
Replace with correct type Drum Unit
5
J8-2 Toner Cartridge TYPE NO. FAIL Type No. stored in ID of Toner Unit does not match with that saved in NVM on main PWB.
•
Replace with correct type Toner Unit 5
J8-3 Counter TYPE NO. FAIL Type No. stored in ID of Total Counter does not match with that saved in NVM on main PWB.
•
Replace with correct type Total Copy Count
Unit
5
J9-1 DRUM UNIT ID No. FAIL Identification No. of Drum Unit is not of Xerox origin.
•
Replace with Xerox Drum Unit
5
J9-2 TONER UNIT ID No. FAIL Identification No. of Toner Unit is not of Xerox origin.
•
Replace with Xerox Toner Unit 5
J9-3 TOTAL COUNTER ID No. FAIL Identification No. of Total Copy Count is not of Xerox origin.
•
Replace with Xerox Total Copy Count Unit
5