![background image](http://html1.mh-extra.com/html/xerox/5915/5915_service-manual_884767023.webp)
2-14
Section 2 Troubleshooting
2.3 level 1 Troubleshooting
2.3.3 Status Code List
STATUS
CODE
NAME
PROBLEM
CORRECTIVE ACTION
REF.
BSD
U1-1
M/C CLOCK FAIL
M/C clock fails to input the signal to Main PWB even once for 0.47 sec., while copying
•
Refer to the U-Code F.I.P.
2
U2-1
LAMP CARRIAGE FAIL-STAND-BY
Lamp carriage doesn’t actuate Optical Registration Sensor for 6.5 sec., during stand-by.
•
Refer to the U-Code F.I.P.
3
U2-2
LAMP CARRIAGE FAIL-POSITION
1: Optical Registration Sensor isn’t turned on within 0.05 sec., after the initial operation
of Lamp Carriage after copying is finished.
2: Optical Registration sensor isn’t turned on within 0.05 sec., after the start of copying.
•
Refer to the U-Code F.I.P.
3
U2-3
LAMP CARRIAGE FAIL-SCAN
Optical Registration sensor isn’t turned on within 0.46 sec., after Lamp Carriage starts scanning.
•
Refer to the U-Code F.I.P.
3
U2-4
LAMP CARRIAGE FAIL-RETURN
Optical Registration sensor isn’t turned on within 2.5 sec., after Lamp Carriage starts scanning.
•
Refer to the U-Code F.I.P.
3
U3-1
LENS POSITION FAIL
Lens Sensor isn’t turned on within 3.1 sec., after the initial operation of Lens.
(i.e. Lens starts moving)
•
Refer to the U-Code F.I.P.
3
U4-1
FUSER THERMISTOR OPEN FAIL
Open or defective circuit of Fuser Thermistor
•
Refer to the U-Code F.I.P.
5
U4-2
FUSER WARM UP FAIL
Fuser Ready is not initiated within 1 min. After the power is on or Front interlock Switch is turned OFF/ON.
•
Refer to the U-Code F.I.P.
5
U4-3
FUSER OVER HEAT FAIL 1
Heater Rod has been on for 10 sec. or more after Fuser Ready
•
Refer to the U-Code F.I.P.
5
U4-4
FUSER OVER HEAT FAIL 2
Heater Rod has been on for 20sec. or more after Cycle Down
•
Refer to the U-Code F.I.P.
5
U4-6
FUSER OVER HEAT SAFETY FAIL
Fuser Thermistor has detected 240
°
C or a higher temperature for straight 0.5sec. or more
•
Enter Diagnostic(C/E) Mode and execute [5-20]
5
U6-4
NVM FAIL
NVM READ/WRITE VERIFY ERROR
•
Refer to the U-Code F.I.P.
2
U8-1
EXPOSURE CONTROL FAIL
Control Mode is not initiated within 0.5 sec., after Exposure Lamp turns on.
•
Refer to the U-Code F.I.P.
3
U8-2
NO ZERO CROSS FAIL
During Fuse Control, no Zero Cross is input for straight 3 sec.
•
Refer to the U-Code F.I.P.
5
U8-4
EXPOSURE VOLTAGE OVER
FAIL
Exposure Sensor signal voltage level is over 2.9V when Exposure Lamp is on.
•
Refer to the U-Code F.I.P.
3
U8-5
EXPOSURE VOLTAGE UNDER
FAIL
Exposure Sensor signal voltage level is under 0.5V at Standard Reflection Plate.
•
Refer to the U-Code F.I.P.
3
Содержание 5915
