![background image](http://html1.mh-extra.com/html/xerox/5915/5915_service-manual_884767013.webp)
2-4
Section 2 Troubleshooting
2.2 Diagnostic(C/E) Mode
2.2 Diagnostic(C/E) Mode
2.2.1 How to Enter Diagnostic(C/E) Mode
Power on while pressing “0” on the keyboard.
•
All the LEDs on Console Panel turn on.
When you press the key pad or the
Stop Clear
button, the three LEDs: “El JAM”, “E3 JAM” and
“TONER EMPTY” starts flashing while the other
LEDs turn off.
2.2.2 Entries of Chain Codes, Function
Codes and Set Values
If you enter a wrong Chain Code or Function
Code, press the
Stop Clear
button and re-enter
a correct one.
•
If you enter an unspecified Chain Code,
Function Code or Set Value, “Er” appears.
2.2.3 How to Exit Diagnostic(C/E) Mode
Set the Power to OFF/ON.
2.2.4 Diagnostic Functions & Operating
Procedures
Input Check
Function:
This displays the input voltage level from the
Sensor or the Switch with “H” or “L”
Procedure:
1. Enter Diagnostic (C/E) Mode.
2. Enter the Chain Code for a part to be
checked and press the
Start
button.
3. Enter the Function Code for a part to be
checked and press the
Start
button.
4. Operate the part to be checked.
•
When the voltage level is high, “H” is
displayed. When it is low, “L” is displayed.
5. When you press the
Stop Clear
button once
during the check, the Function Code Entry
awaiting status is initiated, while you press it
twice, the Chain Code Entry awaiting status
is initiated.
A/D Input Check
Function:
This displays the input voltage level from the
Sensor with
a
digital value.
Procedure:
1. Enter Diagnostic (C/E) Mode.
2. Enter the Chain Code for a part to be
checked and press the
Start
button.
3. Enter the Function Code for a part to be
checked and press the
Start
button.
•
The voltage levels are displayed with the
digital values of 0~FF.
The varying voltage level will change the
display.
4. When you press the
Stop Clear
button once
during the check, the Function Code Entry
awaiting status is initiated, while you press it
twice, the Chain Code Entry awaiting status
is initiated.
Console Button Check (2-1)
Function:
This checks any other button than the
Stop
Clear
one on the Console Panel.
Procedure:
1. Enter Diagnostic (C/E) Mode.
2. Enter Chain Code “2” and press the
Start
button.
3. Enter Function Code “1” and press the
Start
button.
4. Set any other button than the
Stop Clear
one to ON/OFF, then + 2 is added to the
displayed value.
5. When you press the
Stop Clear
button once
during the check, the Function Code Entry
awaiting status is initiated, while you press it
twice, the Chain Code Entry awaiting status
is initiated.
Содержание 5915
