![background image](http://html1.mh-extra.com/html/xerox/5915/5915_service-manual_884767072.webp)
4-37
9. Electrical
Section 4 Disassembly/Assembly/Adjustment
CHAIN 30 CODE TABLE
CHAIN
CODE
FUNCTION
CODE
CURRENT
VALUE
COMPONENT COUNTER
30
1
Tray 1 Feed Counter
4
MSI Feed Counter
CHAIN 40 CODE TABLE
CHAIN
CODE
FUNCTION
CODE
CURRENT
VALUE
COMPONENT COUNTER
40
1
E1 JAM Counter
2
E3 JAM Counter
5
C1 JAM Counter
10
C9 JAM Counter
21
E1 JAM Counter Reset
22
E3 JAM Counter Reset
25
C1 JAM Counter Reset
30
C9 JAM Counter Reset
CHAIN 50 CODE TABLE
CHAIN
CODE
FUNCTION
CODE
SETUP ITEM
SET
VALUE
CONTENT
EXPLANATION
0
inhibit
50
1
Toner Touch Up Function
*1
execute
Only when the new Drum
unit is installed, this sets
up Toner Touch Up
Function at the start of
copying to prevent Talc
Deletion.
0
XC
1
KX
2
Nation Configuration Setup
*2
AP
This supplements a lack of
the exposure light quantity
by the Deve. Bias when it
doesn’t reach its target
value.
0
execute
*1
execute
2
execute
4
Black Band Creation
Function
3
inhibit
Create a black band of
Toner on the Drum to
prevent Talc Deletion.
*0
No
6
Related Products’ L6
Detection
1
Yes
This temporarily inhibits
the detection of L6 when
changes are made to
specification setups of the
machine.
*0
Inhibit
7
Fuser Warm Up Function
1
execute
At the start of an initial
copy with the power on,
this warms up the Fuser
by rotating the Main Motor
for 20 sec .
0
13Phase
8
Copy density selection
*1
7Phase
In case of KX
In case of AP
9
Black Band Function
Time1
0~40
20
10
Black Band Function
Time2
0~40
20
0
Cancellation
1
Cancellation
20
Fuser Over Heat Failure
Clearance
1
Cancellation
U4-6(Fuser Over Heat
Fail) will be cleared.
86
Machine Administrator
Reset
-
-
Set to “1111”.
Содержание 5915
