Xantrex 815-3012-02 Скачать руководство пользователя

Страница: 7 / 76

Precautions When Working With Batteries

975-1057-01-01

DANGER

EXPLOSION HAZARD

• Charge only properly rated (such as 12 V) lead-acid (GEL, AGM, Flooded, or

lead-calcium) rechargeable batteries because other battery types may
explode.

• Do not work in the vicinity of lead-acid batteries. Batteries generate explosive

gases during normal operation. See note #1.

• Do not install and/or operate in compartments containing flammable materials

or in locations that require ignition-protected equipment. See notes #2 and #3.

• When using Lithium-Ion batteries, ensure that the battery pack being used

includes a certified Battery Management System (BMS) with safety controls.

Failure to follow these instructions will result in death or serious
injury.

NOTES

1. Follow these instructions and those published by the battery

manufacturer and the manufacturer of any equipment you
intend to use in the vicinity of the battery. Review cautionary
markings on these products and on the engine.

2. This inverter/charger contains components which tend to

produce arcs or sparks.

3. Locations include any space containing gasoline-powered

machinery, fuel tanks, as well as joints, fittings, or other
connections between components of the fuel system.

Precautions When Working With
Batteries

IMPORTANT

: Battery work and maintenance must be done by

qualified personnel knowledgeable about batteries to ensure
compliance with battery handling and maintenance safety
precautions.

WARNING

BURN FROM HIGH SHORT-CIRCUIT CURRENT, FIRE
AND EXPLOSION FROM VENTED GASES HAZARDS

• Always wear proper, non-absorbent gloves, complete eye protection, and

clothing protection. Avoid touching your eyes and wiping your forehead while
working near batteries. See note #4.

• Remove all personal metal items, like rings, bracelets, and watches when

working with batteries. See notes #5 and #6 below.

• Never smoke or allow a spark or flame near the engine or batteries.
• Never charge a frozen battery.

Failure to follow these instructions can result in death, serious
injury, or equipment damage

Содержание 815-3012-02













































































Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды

Xantrex 815-3012-02, Руководство пользователя

Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды