Xantrex 815-3012-02 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 76

background image

4

975-1057-01-01

IMPORTANT SAFETY INSTRUCTIONS

READANDSAVE THIS GUIDE FORFUTURE REFERENCE

.

This chapter contains important safety instructions for the
Freedom SW Inverter/Charger (Freedom SW-RVC). Each time,
before using the Freedom SW-RVC, READ ALL instructions and
cautionary markings on or provided with the inverter/charger, the
batteries, and all appropriate sections of this guide.

NOTE

: The Freedom SW-RVC contains no user-serviceable

parts.

The following special messages may appear throughout this
bulletin or on the equipment to warn of potential hazards or to call
attention to information that clarifies or simplifies a procedure.

The addition of either symbol to a “Danger” or
“Warning” safety label indicates that an electrical
hazard exists which will result in personal injury if the
instructions are not followed.

This is the safety alert symbol. It is used to alert you to
potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.

DANGER

DANGER

indicates a hazardous situation which, if not avoided,

will result in

death or serious injury.

WARNING

WARNING

indicates a hazardous situation which, if not avoided,

could result

in

death or serious injury.

CAUTION

CAUTION

indicates a hazardous situation which, if not avoided,

could result

in

minor or moderate injury.

NOTICE

NOTICE

is used to address practices not related to physical injury.

IMPORTANT

: These notes describe things which are important for you to know,

however, they are not as serious as a caution or warning.

Please Note

: No responsibility is assumed by Xantrex for any consequences

arising out of the use of this material.

«
...
2
3
4
5
6
...
»

Содержание 815-3012-02













































































Отзывы:

Нет отзывов

Похожие инструкции для 815-3012-02

Бренд: Ramsey Electronics Страницы: 20

MaitreView 4KLite

Бренд: AVLink Страницы: 10

Бренд: Alca Power Страницы: 8

Бренд: S.M.S.L Страницы: 31

CSI 23KTL-CT/US-480

Бренд: CanadianSolar Страницы: 88

Бренд: Icy Box Страницы: 30

Бренд: Millennia Страницы: 2

Бренд: Yuan Страницы: 15

Бренд: Sungrow Страницы: 11

Бренд: GoMax Electronics Страницы: 12

Welbee WB-A350P

Бренд: Daihen Страницы: 150

Бренд: Vanner Страницы: 4

Бренд: Enercell Страницы: 12

PerfectPower PP1000

Бренд: Waeco Страницы: 88

Бренд: Xtreme Страницы: 26

Бренд: Wacker Neuson Страницы: 36

Бренд: ICP DAS USA Страницы: 2

Бренд: Data Connect Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды