Xantrex 815-3012-02 Скачать руководство пользователя страница 16

Страница: 16 / 76

Before You Begin the Installation

Freedom SW-RVC Installation Guide

Before You Begin the
Installation

Before beginning your installation:

Read this entire Installation guide so you can plan the
installation from beginning to end.

Assemble all the tools and materials you require for the
installation.

Review the

Safety Information on page 1.

Be aware of all safety and electrical codes which must be
met.

WARNING

ELECTRICAL SHOCK AND FIRE HAZARD

All wiring shall be done by qualified personnel to ensure
compliance with all applicable installation codes and
regulations.

Do not connect to AC and DC power sources during
installation. Disconnect from all power sources when
servicing.

Disable and secure all AC and DC disconnect devices and
automatic generator starting devices.

Failure to follow these instructions can result in death, serious
injury, or equipment damage

Installation Codes

Governing installation codes vary depending on the specific
location and application of the installation. Some examples
include the following:

The U.S. National Electrical Code (NEC)

The U.S. Code of Federal Regulations (CFR)

The Canadian Electrical Code (CEC)

Canadian Standards Association/CSA Group (CSA) and the
RV Industry Association (RVIA) standards and codes for
installations in RVs

NOTE

: It is the installer’s responsibility to ensure that all

applicable installation requirements are met.

Содержание 815-3012-02













































































Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды

Xantrex 815-3012-02, Руководство пользователя

Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды