Xantrex 815-3012-02 Скачать руководство пользователя страница 9

Страница: 9 / 76

Precautions When Placing the Unit

975-1057-01-01

Precautions When Placing the
Unit

NOTICE

RISK OF INVERTER/CHARGER DAMAGE

• Never allow battery acid to drip on the inverter/charger when reading specific

gravity, or filling battery.

• Never place the Freedom SW-RVC unit directly above batteries; gases from a

battery will corrode and damage the inverter/charger.

• Do not place a battery on top of the inverter/charger.

Failure to follow these instructions can result in equipment
damage.

Regulatory

The Freedom SW-RVC is certified to appropriate US and Canadian
standards. For more information see

Specifications on page 72

The Freedom SW-RVC is intended to be used for recreational
vehicle and commercial applications.

It is not intended for other applications as it may not comply with the
additional safety code requirements needed for those other
applications. See “Limitations On Use” below.

WARNING

LIMITATIONS ON USE

Do not use in connection with life support or vital systems.

Failure to follow these instructions can result in death or serious
injury

Содержание 815-3012-02













































































Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды

Xantrex 815-3012-02, Руководство пользователя

Результаты поиска

Содержание 815-3012-02

Отзывы:

Похожие инструкции для 815-3012-02

Бренды по названию

Популярные бренды