Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 56

Страница: 56 / 64

6-6

PROBLEM

POSSIBLE CAUSE

SOLUTION

Washer Will Not

Turn On.

No power supply.

Power cord broken and/or plug terminal
loose.

Wiring harness open or shorted wiring.

Interface board damaged.

Electronic control board damaged.

Lid switch contact open or shorted.

Water pump clogged.

Water pump damaged.

Brake lining dirty, misadjusted, or worn.

Inlet valve damaged.

Motor or capacitor damaged.

Wiring harness wiring open or shorted.

Brake actuator burned.

Electronic control board damaged.

LEDs On Panel

Do Not Light.

Selected

Program Does

Not Run.

Turn on house breaker or fuse or wait for
power to be restored.

Measure continuity between cable ends.

Connect or replace the wiring harness.

Replace the interface board.

Replace the electronic board.

Check for continuity when closed and no
continuity when open.

Remove the object that is clogging the
water pump.

Replace the water pump.

Clean, adjust, or replace.

Replace the inlet valve (also see “No
Water Inlet”).

See “Motor Does Not Run."

Connect or replace the wiring harness.

Replace the actuator.

Replace the electronic board.

START/OFF keypad not activated.

Lid open.

No water.

No power supply.

Low voltage at main house supply.

Lid switch open.

Lid microswitch wiring harness open or
shorted.

Wiring harness wiring open or shorted.

Electronic control damaged.

Press the START/OFF keypad.

Close the lid (washer does not operate with
lid open).

Check for closed tap or house water supply.

Turn on house breaker or fuse or wait for
power to be restored.

Check the installation.

Check for continuity when closed and no
continuity when open.

Measure continuity between wiring.

Connect or replace wiring harness.

Replace the electronic control.

TROUBLESHOOTING GUIDE

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды