Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 57

Страница: 57 / 64

6-7

No Water Inlet.

(Hot Or Cold)

Tap closed.

Inlet hose clogged.

Water inlet clogged or low water
pressure.

Lid switch open.

Lid microswitch wiring harness open or
shorted.

Hot or cold water inlet valve damaged.

Electronic control damaged.

Open the water tap.

Remove the object that is clogging the inlet
hose or replace the hose.

Unscrew tap hose and proceed with
cleaning procedures recommended in the
Installation Guide.

Check for continuity when closed and no
continuity when open.

Measure continuity between wires.

Replace the water inlet valve.

Replace the electronic control.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Motor Does

Not Run.

Inappropriate electrical installation.

Lid microswitch open or shorted.

Capacitor opened or shorted.

Open coil.

Motor windings open or shorted.

Wiring harness wiring open or shorted.

Electronic control damaged.

Lid switch open.

Lid microswitch wiring harness open or
shorted.

Pressure switch damaged.

Pressure switch wires open or shorted.

Hose, pressure switch damaged.

Motor capacitor damaged.

Brake actuator burned.

Wiring harness wiring open or shorted.

Gearcase assembly locked.

Electronic control damaged.

Call an electrician.

Check for continuity when closed and no
continuity when open.

Discharge capacitor and check with
ohmmeter in Rx100 scale. Meter should
move towards 0 and then towards infinity.

Check for continuity.

Connect or replace the wiring harness.

Replace the electronic control.

Check for continuity when closed and no
continuity when open.

Check continuity between wires.

Replace pressure switch.

Check continuity between wires.

Replace hose or pressure switch.

See "Motor Does Not Run."

Replace the actuator.

Connect or replace the wiring harness.

Replace gearcase assembly.

Replace the electronic control.

Washer Does

Not Agitate.

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды