Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 64

background image

4-3

8.

Remove the two 7/32

″

hex-head screws

from the component cover.

9.

Using a putty knife, pry up on the cover
and release the four tabs of the compo-
nent cover from the top cover. Rotate the
cover down so that it lays on the top of the
cabinet.

Component Cover Screws

Component Cover

Pry Up & Release Tabs

Rotate Component Cover Down

10.

To remove the pressure switch:

a) Squeeze the locking arms in, and push

the pressure switch mounting tab out
of the slot in the dispenser housing.

b) Cut the wire tie from around the pres-

sure switch hose and disconnect the
hose and rubber o-ring from the pres-
sure switch.

c) Cut the wire tie from around the plastic

bag and the pressure switch wires and
remove the bag from the switch.

Pressure Switch Mounting Tab

Wire Tie Around

Wires & Bag

Wire Tie Around
Pressure Switch
Hose & Bag

Continued on the next page.

«
...
29
30
31
32
33
...
»

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Отзывы:

Нет отзывов

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренд: VALBERG Страницы: 96

Бренд: Vax Страницы: 8

Бренд: Zanussi Страницы: 8

Бренд: Zanussi Страницы: 30

Бренд: ZANKER Страницы: 22

Бренд: Kärcher Страницы: 24

Бренд: Parker Страницы: 17

Бренд: Jet-tech Страницы: 10

Бренд: Magic Chef Страницы: 12

Бренд: HERKULES Страницы: 20

Бренд: Monogram Страницы: 88

Бренд: Simpson Страницы: 48

Бренд: Easy-Kleen Страницы: 28

Бренд: Fagor Страницы: 115

Бренд: ZANKER Страницы: 60

Бренд: Wilks USA Страницы: 18

WA90T6250B Series

Бренд: Samsung Страницы: 44

Бренд: Samsung Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды