Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 39

Страница: 39 / 64

4-11

REMOVING THE BRAKE AND GEARCASE ASSEMBLIES

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

Unplug washer or disconnect power.

Turn off the water supply to the washer.

Remove the agitator and basket (see pages
4-6 and 4-7 for the procedures).

Tape the lid closed and lay the washer on
its rear panel so that you can access the
bottom of the unit.

Remove the brake actuator and discon-
nect it from the brake arm (see pages 4-16
and 4-17 for the procedure).

Remove the two carriage bolts and nuts
from the drive motor and remove the mo-
tor and the belt.

Press the locking arms and disconnect the
wiring harness from the drive motor connector.

Remove the green ground wire from the
motor ground terminal.

Motor Connector

Electrical Shock Hazard

Connect green ground wire to ground
terminal.

Failure to do so can result in death or
electrical shock.

WARNING

Remove the 1/2

″

hex-nut from the splutch

pulley and remove the pulley.

10. Unsnap the cam splutch snap-in from the

motor support and remove the snap-in.

11. Remove the four 1/2

″

hex-head bolts from

the motor support.

Cam Splutch Snap-in

12. Remove the splutch spring, slider, and

cam ring from the gearshaft.

Splutch Pulley

Motor Support Bolts

Drive Motor

Splutch Spring

Splutch
Cam Ring

Splutch Slider

Continued on the next page.

Carriage Bolts & Nuts

Ground Wire

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды