Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 58

Страница: 58 / 64

6-8

Outlet hose over 72

″

(1.83 m) in height.

Lid switch open.

Lid microswitch wiring harness broken.

Pressure switch damaged.

Pressure switch or wires broken.

Hose, pressure switch damaged.

Water pump clogged or damaged.

Electronic control damaged.

Outlet hose installed below minimum
height specified 34

″

(85 cm) from washer

base.

Electronic control damaged.

Clothes added after water filling.

Inlet hose improperly connected.

Outlet hose improperly connected.

Pressure switch contacts damaged or
pressure switch hose loose/damaged.

Pressure switch or wires broken.

Seal damaged.

Rubber seal damaged.

Air dome clogged.

Inlet water valve opened.

Electronic control damaged.

Too much detergent.

Lid switch open.

Lid microswitch wiring harness broken.

Wedge not tightened.

Brake actuator burned.

Wiring harness open or shorted.

Pressure switch damaged.

Pressure switch wires open or shorted.

Hose, pressure switch damaged.

Water pump clogged or damaged.

Motor or capacitor damaged.

Mechanism assembly locked.

Electronic control damaged.

PROBLEM

POSSIBLE CAUSE

SOLUTION

Washer Does

Not Drain.

Water Drained

Before End

Of Cycle.

Water Leakage /

Water Level

Overflow.

Install hose correctly.

Check for continuity when closed and no
continuity when open.

Check continuity between wires.

Replace pressure switch.

Check continuity between wires.

Replace hose or pressure switch.

Remove the object that is clogging the
pump or replace the pump.

Replace the electronic control.

Refer to Installation Guide and keep
hose length over 34

″

(85 cm) and below

″

(1.20m)

Replace the electronic control.

Put in clothes before water filling.

Install hose correctly.

Check continuity. Also visually check hose.

Check continuity between wires.

Replace seal.

Replace rubber seal.

Remove the object that is clogging the air
dome.

Replace water inlet valve.

Replace the electronic control.

Wait approximately 30 minutes and repeat
the “Normal Wash” cycle. Make sure that
the correct amount of detergent is used.

Check for continuity when closed and no
continuity when open.

Check continuity between wires.

Tighten the wedge.

Replace the actuator.

Connect or replace the wiring harness.

Replace the pressure switch.

Check continuity between wires.

Replace the hose or pressure switch.

Remove the object that is clogging the
water Pump or replace the pump.

See "Motor Does Not Run."

Replace the mechanism assembly.

Replace the electronic control.

Washer Does

Not Spin.

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды