Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 64

background image

- ii -

WHIRLPOOL CORPORATION assumes no responsibility for any repairs made
on our products by anyone other than Authorized Service Technicians.

FORWARD

This Whirlpool Job Aid “22

″

Compact Automatic Washer” (Part No. 8178436), provides the

technician with information on the installation, operation, and service of the 22

″

Compact

Automatic Washer. It is to be used as a training Job Aid and Service Manual. For specific
information on the model being serviced, refer to the “Use and Care Guide,” or “Tech Sheet”
provided with the washer.

The Wiring Diagram and Strip Circuits used in this Job Aid are typical and should be used for
training purposes only. Always use the Wiring Diagram supplied with the product when servicing
the unit.

GOALS AND OBJECTIVES

The goal of this Job Aid is to provide detailed information that will enable the service technician to
properly diagnose malfunctions and repair the Whirlpool 22

″

Compact Automatic Washer.

The objectives of this Job Aid are to:

• Understand and follow proper safety precautions.
• Successfully troubleshoot and diagnose malfunctions.
• Successfully perform necessary repairs.
• Successfully return the washer to its proper operational status.

Copyright © 2004, Whirlpool Corporation, Benton Harbor, MI 49022

«
1
2
3
4
...
»

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Отзывы:

Нет отзывов

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренд: Glen Dimplex Страницы: 48

Бренд: Campomatic Страницы: 36

HD 10/16-4 Cage

Бренд: Kärcher Страницы: 310

Бренд: Bush Страницы: 36

Бренд: Kärcher Страницы: 16

Бренд: Rac Страницы: 13

Бренд: VONROC Страницы: 76

Бренд: Lavor Страницы: 153

Бренд: Simpson Страницы: 23

Бренд: BENDIX Страницы: 24

Бренд: Hotpoint Страницы: 24

Бренд: Indesit Страницы: 12

Бренд: Kodiak Страницы: 14

Бренд: Asko Страницы: 52

Бренд: Lavor Страницы: 12

CF 1201 - 1 PHASE

Бренд: VALERA Страницы: 2

Бренд: Smeg Страницы: 34

GU2275XTVY - 24" Wide Energy ST

Бренд: Whirlpool Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды