manualshive.com logo in svg

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Стиральная машина Whirlpool LCE4332PQ имеет ёмкость 2,1 кубического фута и предназначена для небольших помещений. Для ознакомления с инструкцией по использованию данного устройства, вы можете бесплатно скачать пользовательское руководство на manualshive.com. Наслаждайтесь удобством и эффективностью этой качественной техники.

Поделиться
Скачать
background image

- iii -

TABLE OF CONTENTS

Page

GENERAL

............................................................................................................................... 1-1

Safety First ......................................................................................................................... 1-1
Model & Serial Number Designations ................................................................................ 1-2
Model & Serial Number Label And Tech Sheet Locations ................................................. 1-3
Specifications ..................................................................................................................... 1-4
Whirlpool Compact Washer Warranty ............................................................................... 1-5

INSTALLATION INFORMATION

........................................................................................... 2-1

Installation Requirements .................................................................................................. 2-1
Permanent Installation Instructions .................................................................................... 2-5
Portable Installation Instructions ...................................................................................... 2-10

PRODUCT OPERATION

........................................................................................................ 3-1

Theory Of Operation .......................................................................................................... 3-1
Washer Use ....................................................................................................................... 3-3

COMPONENT ACCESS

......................................................................................................... 4-1

Component Locations ........................................................................................................ 4-1
Removing The Pressure Switch, Water Inlet Valves, Lid Switch,
   Interface And Electronic Control Boards ......................................................................... 4-2
Removing The Basket ....................................................................................................... 4-6
Removing The Tub ............................................................................................................ 4-8
Removing The Brake And Gearcase Assemblies ............................................................ 4-11
Removing The Capacitor And Drive Motor ...................................................................... 4-14
Removing The Brake Actuator Assembly ........................................................................ 4-16
Removing The Drain Pump ............................................................................................. 4-18

COMPONENT TESTING

........................................................................................................ 5-1

Pressure Switch ................................................................................................................. 5-1
Water Inlet Valve Solenoids ............................................................................................... 5-2
Drive Motor Capacitor ........................................................................................................ 5-2
Brake Actuator ................................................................................................................... 5-3
Drive Motor ........................................................................................................................ 5-4
Drain Pump ........................................................................................................................ 5-4

DIAGNOSTICS & TROUBLESHOOTING

.............................................................................. 6-1

Diagnostics ........................................................................................................................ 6-1
   Time Charts .................................................................................................................... 6-2
   Self Diagnostic Failure—Alarm Codes ........................................................................... 6-3
   Service Routine .............................................................................................................. 6-4
Troubleshooting Guide ...................................................................................................... 6-6

WIRING DIAGRAM & STRIP CIRCUITS

............................................................................... 7-1

Wiring Diagram .................................................................................................................. 7-1
Strip Circuits ...................................................................................................................... 7-2

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Отзывы:

Нет отзывов

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

GE GUD27GSSJ1WW Installation Instructions Manual preview
GUD27GSSJ1WW
Бренд: GE Страницы: 36
Troy-Bilt 020337-2 Operator'S Manual preview
020337-2
Бренд: Troy-Bilt Страницы: 26
Nilfisk-Advance APC 328 Instructions For Use Manual preview
APC 328
Бренд: Nilfisk-Advance Страницы: 24
Magic Chef MCSDW7FCB User Manual preview
MCSDW7FCB
Бренд: Magic Chef Страницы: 25
Fisher & Paykel SINGLE DISHDRAWER DD24SCTB9 Quick Start Manual preview
SINGLE DISHDRAWER DD24SCTB9
Бренд: Fisher & Paykel Страницы: 3
Celsius CDW12 Instruction Manual preview
CDW12
Бренд: Celsius Страницы: 13
Hoover HPA 135 Instructions For Use Manual preview
HPA 135
Бренд: Hoover Страницы: 17
Rac HP009 Instruction Manual preview
HP009
Бренд: Rac Страницы: 13
Indesit EWDE 71280 Instructions For Use Manual preview
EWDE 71280
Бренд: Indesit Страницы: 84
Amica WA484100W Quick Start Manual preview
WA484100W
Бренд: Amica Страницы: 2
TOPMAQ CLWA5500 Owner'S Manual preview
CLWA5500
Бренд: TOPMAQ Страницы: 30
Hotpoint Ariston AQUALTIS AQLF8F 292 U Instructions For Installation And Use Manual preview
AQUALTIS AQLF8F 292 U
Бренд: Hotpoint Ariston Страницы: 64
Viking Professional & Designer 200 Series Installation Manual preview
Professional & Designer 200 Series
Бренд: Viking Страницы: 12
Kärcher Trailer HDS Series Operator'S Manual preview
Trailer HDS Series
Бренд: Kärcher Страницы: 32
inventum RVW6027AB Instruction Manual preview
RVW6027AB
Бренд: inventum Страницы: 88
Haier HNS1260TVE Service Manual preview
HNS1260TVE
Бренд: Haier Страницы: 27
Haier HNS1260TVE Operating Instructions Manual preview
HNS1260TVE
Бренд: Haier Страницы: 54
Haier HWM120-01 User Manual preview
HWM120-01
Бренд: Haier Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды