Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 37

Страница: 37 / 64

4-9

11. Using pliers, press in on the locking tabs,

and unsnap the five wire standoffs from
the bottom of the tub. Make sure that all of
the lower wiring is removed from the tub.

12. Remove the two screws from the shield

and remove the shield from the tub.

5 Wire Standoffs

Shield & Screws

Tub (Bottom)

13.

OPTIONAL STEP:

To contain the grease

on the suspension cups at the bottom of
the tub, slide a plastic sandwich bag over
each of the cups, and secure each with a
rubber band.

Plastic Bag With
Rubber Band

14. Stand the washer in its upright position.

IMPORTANT:

Place a plastic drop cloth under

the cabinet to protect the floor covering.

15. Remove the top cover and lean it back

against a wall.

16. Lift the rubber snubber straps off the four

tub pins.

NOTE:

Have a shop cloth ready to clean off any

grease from your hands.

17. Remove the four suspension rods from

their suspension balls. To remove a rod:

a) Grasp the rod several inches below

the suspension ball, then pry up with a
small screwdriver, and unsnap the rod
from the ball.

Rubber

Snubber

Straps

Continued on the next page.

Pry Up &

Unsnap Rod

10. Pull the tub support assembly straight

forward until the rubber seal at the center
of the tub opening is free, and set the
assembly aside.

Tub Support Assembly

Suspension Cup

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды