Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 64

background image

4-8

REMOVING THE TUB

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before
operating.

Failure to do so can result in death or
electrical shock.

WARNING

1.

Unplug washer or disconnect power.

2.

Turn off the water supply to the washer.

3.

Remove the top cover from the washer
and lean it back against a wall (see page
4-2 for the procedure).

4.

Remove the agitator and basket (see pages
4-6 and 4-7 for the procedures).

5.

Reinstall the top cover on the washer and
secure it with only one of the rear screws.
You will remove the top cover again later.

6.

Lay the washer on its rear panel so that
you can access the bottom of the unit.

7.

Remove the drain pump and hose from
the tub (see steps 4 through 6 on page
4-18 for the procedure).

NOTE:

You can

leave the end of the hose connected to the
drain pump housing.

8.

Disconnect the wire connectors from the
following components (see the photo at
the lower left for the component locations):

a) Brake actuator
b) Drive motor (and green ground wire)
c) Capacitor

Brake Actuator

Drive Motor

Drain Pump

Electrical Shock Hazard

Connect green ground wire to ground
terminal.

Failure to do so can result in death or
electrical shock.

WARNING

9.

Remove the five hex-head bolts from the
tub support.

3 Bolts

2 Bolts

Capacitor

«
...
34
35
36
37
38
...
»

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Отзывы:

Нет отзывов

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 16

Бренд: Fagor Страницы: 108

Appliances Profile PFWS4605

Бренд: GE Страницы: 88

Бренд: Admiral Страницы: 32

Бренд: NEFF Страницы: 32

Бренд: Indesit Страницы: 24

Бренд: Landa Страницы: 50

Бренд: Ariston Страницы: 12

Бренд: Danby Страницы: 44

Бренд: Teka Страницы: 85

Бренд: Maytag Страницы: 20

Бренд: Gaggenau Страницы: 68

Бренд: Rangemaster Страницы: 28

Бренд: Thermador Страницы: 66

Бренд: Supera Страницы: 15

Бренд: Smeg Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды