Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity Скачать руководство пользователя страница 11

Страница: 11 / 64

2-1

INSTALLATION INFORMATION

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Assemble the required tools and parts before
starting installation. Read and follow the in-
structions provided with any tools listed here.

The parts supplied are in the washer basket.

Portable Installation

Tools needed:

• Pliers that open to 1-9/16

″

(3.95 cm)

• Utility knife
• Flashlight (optional)

Parts supplied:

Permanent Installation

Tools needed:

• Pliers that open to 1-9/16

″

(3.95 cm)

• Flashlight (optional)
• Adjustable or open end wrench 9/16

″

(14 mm)

• Level
• Wood block
• Utility knife
• Measuring tape

Parts supplied:

A. Silver, double-wir e hose clamp (for the bottom of the

drain hose)

B. Faucet adapter
C. Fill-and-d rain hose

NOTE:

To change a permanent installation to

a portable installation, kit

#285768

is required.

A. Drain hose
B. Silver, double-wire hose clamp

(for the botto m of the drain hose)

C. Yellow, single-w ire hose clamp

(for the top of the drain hose)

D. Water inlet hoses (2)

E. Flat water inlet hose

washers (4)

F. Beaded tie strap

NOTE:

To change a portable installation to a

permanent installation, kit

#4396746

is required.

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

































































Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды

Whirlpool LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity, Руководство пользователя

Результаты поиска

Содержание LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Отзывы:

Похожие инструкции для LCE4332PQ - 22" Washer w/2.1 cu. Ft. Capacity

Бренды по названию

Популярные бренды