Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 72

Страница: 72 / 196

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

6 Operation

83309302 1/2018-05 La

72-196

6.6.1.6 Domestic hot water

Info

Domestic hot
water

Information

Description

1.7.1
Status

Current operating mode of DHW circuit.

Standby via system program switch
Time program - normal
Time program - setback
DHW mode activated
Normal, setback, standby via input H2

1.7.2
Flow setpoint
temperature DHW

Required flow setpoint temperature for DHW loading.

The flow set temperature results from the

DHW setpoint temperature

and

the

flow setpoint temperature increase

7.1.3

1.7.3
DHW setpoint
temperature

DHW setpoint temperature of current operating mode (normal or setback).

1.7.4
DHW temperature

Current temperature at the DHW sensor (B3).

1.7.5
Return flow temperature
circulation

Current temperature at the return flow sensor (T1) of the circulation line.

Only on compact version WAS 100.

1.7.6
DHW pump

Current operating mode of DHW load pump.

Off
On

1.7.7
Status DHW mode

Current operating mode of DHW circuit.

Off
Standby
Burner start
Tap operation
Comfort keep warm function
Top-up heating following tap drawdown
Pump run-on
SCOT calibration in DHW

1.7.8
DHW outlet setpoint
temperature

Required setpoint of DHW outlet temperature.

1.7.9
DHW actual outlet
temperature

Current temperature at the DHW outlet sensor (T1).

Only on compact version WAS … Power.

1.7.12
DHW
temperature bottom

Current temperature at the DHW sensor switch-off (T2).

Only on compact version WAS … Power.

Содержание WTC-GB 15-B Compact





































































































































































































Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Похожие инструкции для WTC-GB 15-B Compact

Бренды по названию

Популярные бренды

Weishaupt WTC-GB 15-B Compact, Инструкция по установке и эксплуатации

Результаты поиска

Содержание WTC-GB 15-B Compact

Отзывы:

Похожие инструкции для WTC-GB 15-B Compact

Бренды по названию

Популярные бренды