Weishaupt WTC-GB 15-B Compact Скачать руководство пользователя страница 155 | Manualshive

Страница: 155 / 196

background image

Installation and operating instruction
Gas condensing unit WTC-GB 15-B Compact and WTC-GB 25-B Compact

12 Technical documentation

83309302 1/2018-05 La

155-196

WTC input H2

The function (contact position) of input H2 can be rotated using parameter

Input

H2 inverted

.

Setting

Explanation

Off

Input not used

System standby with
frost protection

The WTC is disabled for heating and DHW mode when the contact is closed.
Frost protection is activated.

Emergency-Off
heat exchanger

The system is disabled for heating and DHW mode when the contact is open.
Frost protection is not activated.

Block heating/
DHW mode

The WTC is disabled for heating and DHW mode when the contact is closed.
Frost protection is activated.

Generator block
DHW mode

The WTC is disabled for DHW mode when the contact is closed. Frost protection
is not activated.

DHW 1: standby

DHW mode is disabled when the contact is closed. Frost protection is activated.

DHW 1: setback

When the contact is closed, the system heats to setback setpoint. The DHW pro-
gram is ineffective.

DHW 1: normal

When the contact is closed, the system heats to normal setpoint. The DHW pro-
gram is ineffective.

DHW 1:
Boost/button

If the button on the input is pressed, the WTC loads the DHW storage tank in
DHW circuit 1 once to the normal DHW setpoint temperature. An increased de-
mand for hot water during setback operation can be met using the DHW boost
function.

Forward signalling via
portal

When the contact is closed, a message is forwarded to the WEM portal.

DHW 1:
circulation/button

Only if the hydraulic

circulation pump

is set to

time cont

button (H2)

in the commissioning wizard.

If the button on the input is pressed, the WTC activates the output for the circula-
tion pump. The output to which the pump is connected must be set to hot water
circuit 1: circulation. The run time of the pump is determined via parameter

pump

run time via button

.

Heating circuit (extension module WEM-EM-HK) input H1

Setting

Explanation

no function

Input not used

Standby

heating mode is disabled when the contact is closed. Frost protection is activated.

Heating circuit activ-
ated
setback operation

When the contact is closed, the system heats to setback setpoint. The relevant
heating program is ineffective.

Heating circuit activ-
ated
normal operation

When the contact is closed, the system heats to normal setpoint. The relevant
heating program is ineffective.

Heating circuit activ-
ated
comfort operation

When the contact is closed, the system heats to comfort setpoint. The relevant
heating program is ineffective.

Heating circuit activ-
ated
special level

When the contact is closed, the system heats to special level. The relevant heating
program is ineffective.

Emergency-Off

heating mode is disabled when the contact is open. Frost protection is not activ-
ated.

«
...
153
154
155
156
157
...
»

Содержание WTC-GB 15-B Compact





































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для WTC-GB 15-B Compact

Бренд: Zoeller Страницы: 4

Бренд: Mallory Страницы: 7

Бренд: Jetmaster Страницы: 23

Бренд: Danfoss Страницы: 34

Бренд: Danfoss Страницы: 52

Бренд: Saxon Страницы: 12

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: Argo Страницы: 10

Desk Friend DDF250

Бренд: Dimplex Страницы: 4

Бренд: VONROC Страницы: 60

Бренд: REHOBOT Страницы: 14

Бренд: Sinus Jevi Страницы: 13

Бренд: Domus Страницы: 2

Бренд: EDM Product Страницы: 25

Бренд: Calorex Страницы: 28

Бренд: Sentiotec Страницы: 28

Бренд: Xvent Страницы: 29

Бренд: LVI Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды